曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  strands or cause damage to the center conductor. 
R  (2) Crimping procedure 
R  (Ref. Fig. 006) 
R  - Install the wire core in the contact, until the core insulation 
R  touches the contact. 
R  - Crimp with the applicable tool. 
R  - Install the contact in the connector body until the core insulation 
R  touches the connector dielectric. 
R  - Open the braid and install it above the rear of the connector body. 
R  - Slide the ferrule under the braid until it touches the connector 
R  body 
R  - Crimp with the applicable tool.

 

R C Type Coaxial Connectors - Stripping and Crimping Tools R NSA938661 R Figure 006

20-44-32 Page 9

 ________________________________________________________
COAXIAL CONNECTORS - HN TYPE - DESCRIPTION AND OPERATION
 _______
1. General
R HN type coaxial connectors installed on aircraft have the codes that follow:
 -NSA938608
 _________2. NSA938608
 A. P/N identification
 (Ref. Fig. 001)
 NSA938608 -01

 | | | | | --------------- Wire type code | | | -------------------- Type code | - (dash) : Right receptacle | | FC : Right angle plug | --------------------------- Standard P/N
 B. P/N characteristics
 (1) Temperature Minimum operating temperature is -55 deg.C (-67.00 deg.F). Maximum operating temperature is 155 deg.C (311.00 deg.F)
 C. Connection procedure
 (1)
 Wire stripping
 (Ref. Fig. 002)

 -Strip the wire to the size "A". Make sure that you do not cut the shield braid strand or cause damage to the center conductor.

 (2)
 Crimping procedure
 (Ref. Fig. 003)

 

 -Install in this order the cap, the washer and the seal.
 -Open and comb the braid along the wire core.
 -Install the braid support on the wire.
 -Turn the braid above the braid support cone and cut it on the flange level.
 -Strip the wire to agree with size "B" and "C".
 -Solder the contact on the wire core. R

20-44-33 Page 1

R HN Type Coaxial Connectors - Layout R NSA938608 R Figure 001

20-44-33 Page 2

R HN Type Coaxial Connectors - Wire Stripping and Crimping Tools R NSA938608 R Figure 002

20-44-33 Page 3

R HN Type Coaxial Connectors - Crimping Procedure R NSA938608 R Figure 003

20-44-33 Page 4

 -
Install the seal and the washer.

 -
Install the cap, tighten to applicable torque.

 

20-44-33 Page 5
 Jan 01/03
R

 _________________________________________________________
COAXIAL CONNECTORS - MHV TYPE - DESCRIPTION AND OPERATION
 _______
1. General
R MHV type coaxial connectors installed on aircraft have the codes that follow:
 -NSA938604
 _________2. NSA938604
 A. P/N identification
 (Ref. Fig. 001)

 NSA938604  F 02 | | | | | ---------- Wire type code | | | --------------- Type code | F : Right receptacle | | TC : Square flange bulkhead connector | ---------------------- Standard P/N
 B. P/N characteristics
 (1) Temperature Minimum operating temperature is -54 deg.C (-65.20 deg.F). Maximum operating temperature is 200 deg.C (392.00 deg.F).
 C. Connection procedure
 (1)
 Wire stripping
 (Ref. Fig. 002)

 -Strip the wire to the size "A". Make sure that you do not cut the shield braid strand or cause damage to the wire core.

 (2)
 Crimping procedure
 (Ref. Fig. 003)

 

 -Install in this order the cap, the washer and the seal.
 -Open and comb the braid along the wire core.
 -Install the braid support on the wire.
 -Turn the braid above the braid support cone and cut it on the flange level.
 -Strip the wire to agree with size "B" and "C".
 -Solder the contact on the wire core. R
 -Install this assembly in the body.

20-44-34 Page 1

 MHV Type Coaxial Connectors - Layout
 NSA938604
 Figure 001

 

20-44-34 Page 2

 MHV Type Coaxial Connectors - Wire Stripping and Crimping Tools
 NSA538604
 Figure 002

 

20-44-34 Page 3

 MHV Type Coaxial Connectors - Crimping Procedure
 NSA938604
 Figure 003

 

20-44-34 Page 4

 -
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 3(51)