20-43-42 Page 5
Pressure Seal (Compound Filled) - Sealing Procedure ABS0122 R Figure 002
20-43-42 Page 6
Pressure Seal (Compound Filled) - Sealing Procedure ABS0122 R Figure 003
20-43-42 Page 7
Pressure Seal (Compound Filled) - Sealing Procedure ABS0122 R Figure 004
20-43-42 Page 820-43-42 Page 9
- Squeeze the cables together with a cable tie.
- Center the cables in the pressure seal.
- Complete the filling operation.
- Wait until SEALANTS (Material No. 09-052) or (Material No. 09-012E)
is fully cured.
- Loosen the coupling nut.
- Remove the cable tie behind the washer.
- Remove the plastic washer.
- Remove any BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004)
runs.
- Remove any SEALANTS (Material No. 09-052) or (Material No. 09-012E)
runs.
- Screw the coupling nut of the sheath on the pressure seal.
R D. Associated items
R - Backshell ABS1365 and ABS1366
R (1) P/N Identification
R (Ref. Fig. 005)
R ABS1365 - 22 - 20 B 1
R ABS1366 - 22 - 24 B 1
R | | | | |
R | | | | ------ Pressure seal type code
R | | | --------- Harness protection code: B or C
R | | ------------- Conduit size code
R | ------------------ Shell size code
R ------------------------ Standard P/N
R (2) P/N Characteristics
R (a) Temperature
R Minimum operating temperature is -55 DEG.C (-67.00 DEG.F)
R Maximum operating temperature is 175 DEG.C (347.00 DEG.F)
R (b) Harness protection code
R (Ref. Fig. 005)
R ------------------------------------------------------------------
R | Code | Harness protection |
R |---------|------------------------------------------------------|
R | B | Overbraiding |
R |---------|------------------------------------------------------|
R | C | Braided conduit used with ABS0887 convoluted conduit |
R ------------------------------------------------------------------
R Pressure Seal (Compound Filled) - P/N Characteristics R ABS1365 and 1366 R Figure 005
20-43-42 Page 1020-43-42 Page 11
_________3. NSA934710
A. P/N Identification NSA934710 T 11 | | | | | ------------- Type code | ------------------ Part code -------------------------- Standard P/N
B. P/N Characteristics
(1) Temperature Operating temperature is 105 DEG.C (221.00 DEG.F)
R (2) Part code and type (Ref. Fig. 006) T = Seal E = Spring spacer
C. Procedure
R R R R R R R R R _______WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL MATERIALS ONLY WITH A GOOD FLOW OF AIR THROUGH THE WORK AREA. THESE MATERIALS ARE POISONOUS AND FLAMMABLE AND SKIN IRRITANTS. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Materials and tools - Adhesive tape (Not specific). - SEALANTS (Material No. 09-002) or (Material No. 09-016). - CLEANING AGENTS (Material No. 11-004A) or equivalent. - Extrusion gun : SEMCO model 650 or PYLES model 950. - Dia 4 mm (0.1574 in.) polyethylene nozzle. - SEMCO cartridge.
(2) Preparation
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 3(13)
