20-44-29 Page 7
R Miscellaneous Rectangular Connectors - P/N Characteristics R ABS1152-003 and ABS1152-004 R Figure 004
20-44-29 Page 8
Miscellaneous Rectangular Connectors - Connection arrangement DAN410 R Figure 005
20-44-29 Page 9
R _____7. E0125
A. P/N identification
E0125-60-33-S | | | | | | | ------ Contact type code --| P = pin | | | | S = socket | | | | | -------- Housing type code | 33 = male | | | 34 = female | | | ----------- Contact arrangement code | ---------------- Standard P/N
B. P/N Characteristics
(1) Contact arrangement R (Ref. Fig. 006)
(2) Polarization Polarization is done on two corners of the housing.
20-44-29 Page 10
Miscellaneous Rectangular Connectors - Connection Arrangement E0125 R Figure 006
20-44-29 Page 1120-44-29 Page 12
R _________8. NSA938355
A. P/N Identification NSA938355 E 19 P | | | | | | | | |Contact arrangement code | | | -------|P : Male | | | |S : Female | | | | | ----------- Number of contact | | | --------------- Shell size code | ---------------------- Standard P/N
B. P/N characteristics
R (1) Contact arrangement (Ref. Fig. 007)
R R ________________9. Connection Table (Ref. Fig. 008)
Miscellaneous Rectangular Connectors - Connection Arrangement NSA938355 R Figure 007
20-44-29 Page 13
R Miscellaneous Rectangular Connectors - Connection Table R Figure 008
20-44-29 Page 14
R ______________________________________________
COAXIAL CONNECTORS - DESCRIPTION AND OPERATION
_______1. General
R This chapter concerns description ,installation and identification of
R coaxial connectors used on aircraft:
R _________________________2. Structure of the chapters
R A. BNC type coaxial connectors (20-44-31)
R B. C type coaxial connectors (20-44-32)
R C. HN type coaxial connectors (20-44-33)
R D. MHV type coaxial connectors (20-44-34)
R E. N type coaxial connectors (20-44-35)
R F. TNC type coaxial connectors (20-44-36)
R G. Miniature coaxial connectors (20-44-37)
R H. Miscellaneous coaxial connectors (20-44-39)
20-44-30 Page 1
_________________________________________________________
COAXIAL CONNECTORS - BNC TYPE - DESCRIPTION AND OPERATION
_______1. General
BNC type coaxial connectors installed on aircraft have the codes that follow:
-E0460
-NSA938601
-NSA938603
R _____2. E0460
A. P/N identification
(Ref. Fig. 001)
E0460 F 02 | | | | | ---------------- Wire type code | 01 : EO293XF | | | 02 : EO406WD | | | 03 : NSA935344XE | | | 04 : EN4604-003WZ | | | --------------------- Type code | F : Right receptacle | | TC : Square flange bulkhead connector | | P : Right plug | --------------------------- Standard P/N
B. P/N characteristics
(1) Temperatures Minimum operating temperature is -65 deg.C (-85.00 deg.F). Maximum operating temperature is 165 deg.C (329.00 deg.F).
C. Connection procedure
(1) Wire stripping
(Ref. Fig. 002)
-Put the heat shrinkable sleeve then the ferrule on the wire before you strip it to prevent the deformation of the shield braid.
-Strip the wire. Make sure that you do not cut the shield braid strands or cause damage to the center conductor.
20-44-31 Page 1
R BNC Type Coaxial Connectors - Layout E0460 Figure 001
20-44-31 Page 2
BNC Type Coaxial Connectors - Stripping and Shrinking Tools
E0460
Figure 002
20-44-31 Page 3
Apr 01/04
R
(2) Crimping procedure
(Ref. Fig. 003, 004, 005)
(a) Crimping of rear ferrule :
-Make sure that the heat shrinkable sleeve and the ferrule are in position on the wire.
-Install the cap on the braid support.
-Move the braid support below the braid.
-Install the ferrule on the braid and against the cap. Crimp with the applicable tool. Trim the braid flush with the cap.
-For E0460-P-03 only : . Install the heat shrinkable sleeve on the ferrule. . Shrink the sleeve with the applicable tool.
(b) Crimping of contact and assembly :
-
For E0460-01 and 02 only : . Install the insulating washer against the cap. . Install the contact on the wire core against the insulating washer. Crimp with the applicable tool. . Install the contact in the dielectric and install the assembly in the connector body. . Tighten cap at the applicable torque. Make a red line on the connector body and the cap to show that it is tight. . Install the heat shrinkable sleeve on the cap, on the body. Shrink the sleeve to let the red line stay apparent.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 3(48)
