Splices - Stripping and Crimping Tools ABS0249 R Figure 001

20-43-11 Page 220-43-11 Page 3

R  - Do the same procedure from step 2 for the other end of the splice. 
R  - Do a check to make sure that the splicing is correct.
R  _____3. E0360 
R  A. P/N Identification 
R  E0360RK2220 
R  | | 
R  | | | R = Splice Code 
R  | | | K = Type 
R  | |------------- Reference N. | 22 = Sequence No. 
R  | | 20 = Size Code. 
R  | 
R  -------------------- Standard P/N 
R  B. P/N Characteristics
R  ____NOTE : EO360 is an assembly which has: 
R  - 2 sleeves NSA937210MBXXXX 
R  - 1 splice NSA936812-XX 
R  Two types of splice barrels can be available. 
R  The installation is the same. 
R  (1) Temperature 
R  Minimum operating temperature is -55 deg.C (-67.00 deg.F). 
R  Maximum operating temperature is 260 deg.C (500.00 deg.F). 
R  C. Connection Procedure 
R  (Ref. Fig. 002) 
R  (1) Insulation 
R  - Do the insulation with the shrinkable sleeves delivered: 
R  Install these sleeves on the wires before stripping. 
R  Shrinking is made after crimping. 
R  (2) Wire stripping 
R  - Use the applicable tool. 
R  - Strip the wire to the length "A" . 
R  (3) Crimping 
R  (Ref. Fig. 003) 
R  - Use the applicable crimping tool related to the splice reference 
R  number. 
R  - Make sure that the insulation sleeves are on the wires. 
R  - Put one end of the splice in the crimping tool die. 
R  - Make sure that the splice is in the correct position against the 
R  positioner.

 Butt Splices - P/N Characteristics and Tools E0360 R Figure 002

20-43-11 Page 4

 Butt Splices - Crimping Tools E0360 R Figure 003

20-43-11 Page 520-43-11 Page 620-43-11 Page 7

R  ____NOTE : Depending on the barrel type, the position against the 
R  positioner is not the same. 
R  - Close the crimping tool handles sufficiently to hold the splice in 
R  position but do not crimp at this stage. 
R  - Put the stripped end of the wire in the splice barrel. 
R  - Tightly hold the wire in the barrel. 
R  - Crimp the splice. To do this, fully close the tool handles until 
R  the safety ratchet releases. 
R  - Remove the splice from the crimping tool. 
R  - Do the same procedure from step 2 for the other end of the splice.
R  ____NOTE : For barrel type 1 only, the second crimping operation must be 
R  done diametrically opposite to the first one. 
R  For barrel type 2, the two crimping operations must be along 
R  the brazing seam centerline and positioned on the same side. 
R  - Do a check to make sure that the splicing is correct. 
R  (4) Insulation sleeve shrinking 
R  - Put the sleeve 1 (the shorter sleeve) in the correct position on 
R  the splice. 
R  - Shrink the sleeve with the applicable tool. 
R  - Wait until the sleeve is cold. 
R  - Put the sleeve 2 (the longer sleeve) in the correct position on the 
R  splice. 
R  - Shrink the sleeve with the applicable tool. 
R  - Make sure that the sleeves are in the correct condition.

 _____4. E0541
 A. P/N Identification
 E0541-10 
R  | |-----------Splice Size Code
 |----------------Standard P/N
 B. P/N Characteristics 
R  (Ref. Fig. 004)
 (1) Temperature
 Minimum operating temperature is -65 deg.C (-85.00 deg.F).
 Maximum operating temperature is 150 deg.C (302.00 deg.F).
 (2) Materials 
R  There are 1 type of splice validated :
 - tin-plated splice 
R
 C. Connection Procedure 
R
 (1) Insulation 
R 
R  - Put the shrinkable sleeve delivered on the wires before stripping.
 Shrinking is done after crimping. 
R  - For E0807 WX26 cable, make sure that the heat shielded sleeve 
　
中國(guó)航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 3(2)