R 1EFF : 301-399, 1 27-54-46Page 435 1 1 May 01/04 1 1 1CES 1

R  (3) Move the flap carriage (26) along the flap track (4). The full travel 
R  of the flap carriage (26) must be smooth. 
R  (4) Tighten the aft adjuster screw (22) sufficiently to decrease the 
R  dimension 'X' to 0.05 mm (0.002 in.). Do step 3 again. 
R  (5) Tighten the forward adjuster screw (22) sufficiently to decrease the 
R  dimension 'Y' to 0.05 mm (0.002 in.). Do step 3 again. 
R  (6) If the flap carriage (26) does not move smoothly along the flap track 
R  (4), then loosen the applicable adjuster screw (22) sufficiently 
R  until it does. 
R  (7) Install the lockplate (21) on the forward adjuster screw (22). One of 
R  the holes in the lockplate (21) must align with the hole in the flap 
R  carriage (26). If necessary, tighten the forward adjuster screw (22) 
R  to align the holes. Do step 6 again. 
R  (8) Install the forward lockbolt (17) through the lockplate (21). 
R  (9) Install the lockplate (21) on the aft adjuster screw (22). One of the 
R  holes in the lockplate (21) must align with the hole in the flap 
R  carriage (26). If necessary, tighten the aft adjuster screw (22) to 
R  align the holes. Do step 6 again. 
R  (10) Install the aft lockbolt (17) through the lockplate (21). 
R  (11) Safety the forward and aft lockbolts (17) independently with 
R  MISCELLANEOUS (Material No. 19-010). 
R  Subtask 27-54-46-420-052-A 
R  D. Continue the Installation of the No. 2, 3 and 4 Flap Carriages 
R  (1) Tighten the nuts (20) and safety them independently with 
R  MISCELLANEOUS (Material No. 19-010). 
R  (2) If a new flap carriage (26) has been installed, make sure that the 
R  nuts (25) are hand tight only. 
R  NOTE : The nuts (25) are torque tightened and safetied when the flap____ 
R  is installed. 

R 1EFF : 301-399, 1 27-54-46Page 436 1 1 May 01/04 1 1 1CES 1

R R R R R R  (3) Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to: - the bolts (7), the washers (12) and the nuts (11) - the bolts (9) and (13), the washers (8) and (14), and the nuts (15) and (16) - the forward lockbolt (17) and the aft adjuster screw (19) - the hinge bolts (18) and the nuts (20). 
R R  (4) Lubricate the flap carriage (26) with COMMON GREASE (Material No. 04-024) through the carriage roller greasers (6). 
R  Subtask 27-54-46-410-050-A 
R  E. Close Access 
R R  (1) Make sure that the work area is clean and clear of tool(s) and other items. 
R R R R R  (2) Install the applicable flap: - for the No. 2 carriage, the inboard flap (Ref. TASK 27-54-61-400-003) - for the Nos. 3 and 4 carriages, the outboard flap (Ref. TASK 27-54-62-400-002). 
R R  (3) Make sure that the work area is clean and clear of tool(s) and other items. 
R  **ON A/C ALL
 Subtask 27-54-46-865-052
 F. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV, 10CV, 12CV.
 Subtask 27-54-46-710-050
 G. Operational Test
 (1) Install the safety collar on the circuit breakers 10CV and 12CV.
 (2) Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever on panel 114VU.
 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.

 (a) Retract the flaps fully (Ref. TASK 27-50-00-866-009).
 (3) Do an operational test of the flaps (Ref. TASK 27-54-00-710-001).
 5. Close-up
________ Subtask 27-54-46-942-051
 A. Removal of Equipment
 (1)
 Remove the safety barriers.

 (2)
 Remove the warning notice(s).

 (3)
 Remove the access platform(s).

 (4)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 1EFF : ALL 1 27-54-46Page 438 1 1 May 01/04R 1 1 1CES 1

R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 TASK 27-54-46-000-005
 Removal of the Pendulum of the No. 1 Flap Track Carriage
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱5(73)