(2)
 Do these steps if the bolt holes of the actuator assembly and the
 structure do not align:

 (a)
 Put the universal joint (1) in the torque limiter.

 (b)
 Turn the universal joint (1) until the bolt holes align.

 (c)
 Remove the universal joint (1).

 (3)
 Put a countersunk washer (18) on a bolt (17), with the countersink
 adjacent to the head of the bolt.

 (4)
 Install this bolt (17) with the countersunk washer (18), a washer

 (20) and a nut (19) in the applicable hole (Ref. TASK 20-28-00-912-004):
 -
FOR 6233CM
 in the LH wing bonding position

 -
FOR 6283CM
 in the RH wing bonding position.
 Do not tighten in this step. Do not apply sealant.

 (5)
 Apply a layer of SEALANTS (Material No. 09-018) or SEALANTS (Material No. 09-019) to the shanks of the bolts (17).

 (6)
 Put the countersunk washers (18) on the bolts (17), with the
 countersink adjacent to the heads of the bolts.

 (7)
 Install the remaining bolts (17), the washers (20) and the nuts (19).

 (8)
 TORQUE all the nuts (19) in a diagonally opposite sequence to between

 2.8 and 3.0 m.daN (20.64 and 22.12 lbf.ft).

 (9)
 Do an electrical bonding check between the structure and the
 applicable bolt (Ref. TASK 20-28-00-869-002):

 -
FOR 6233CM
 in the LH wing bonding position

 -
FOR 6283CM
 in the RH wing bonding position.

 (10) Seal the bolt (17), the countersunk washer (18), the washer (20) and the nut (19) in the applicable hole (Ref. TASK 20-28-00-912-004):
 -
FOR 6233CM
 in the LH wing bonding position

 -
FOR 6283CM
 in the RH wing bonding position.

R 1EFF : 001-049, 051-061, 101-105, 201-203, 1 27-54-49Page A424 1 1 May 01/05 1 1 1CES 1

 (11)
 Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to these remaining items:

 -
the bolts (17)

 -
the washers (18) and (20)

 -
the nuts (19).

 (12)
 Open the bottom of the two vent covers (6).

 (13)
 Put the 4 mm (0.1574 in.) dia. rod through the vent into each hole of the bearing to make sure the holes are not blocked.

 (14)
 Close the bottom vent cover (6).

 (15)
 Install the universal joint (1) so that the flanges align with the torque shaft (2).

 (16)
 Install the torque shaft (2) (Ref. TASK 27-54-45-400-013):

 -
FOR 6233CM
 install 6232CM

 -
FOR 6283CM
 install 6282CM.

 (17)
 Install the Asymmetry Position Pick-off Unit (APPU) (4) (Ref. TASK 27-51-18-400-001).

R **ON A/C 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
 Subtask 27-54-49-420-066-A
 D. Installation of the Flap Track 4 Actuator 6233CM(6283CM)
 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 CAUTION : SUPPORT THE ACTUATOR, WHICH CAN WEIGH UP TO 10.5kg (23.2lbs).
_______ THIS WILL PREVENT DAMAGE TO THE RELATED STRUCTURE AND EQUIPMENT.

 (1)
 Turn the actuator drive, as necessary, and engage the actuator drive in the flap drive lever.

 (2)
 Do these steps if the bolt holes of the actuator assembly and the
 structure do not align:

 (a)
 Put the universal joint (1) in the torque limiter.

 (b)
 Turn the universal joint (1) until the bolt holes align.

 (c)
 Remove the universal joint (1).

 (3)
 Put a countersunk washer (10) on a bolt (9), with the countersink
 adjacent to the head of the bolt.

 (4)
 Install this bolt (9) with the countersunk washer (10), washers (11) and a nut (12) in the applicable hole (Ref. TASK 20-28-00-912-004):

 -
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱5(131)