R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
27-54-45-991-001-A Fig. 401A
**ON A/C ALL
27-54-45-991-002 Fig. 402
3. Job Set-up
__________
**ON A/C 001-049, 051-061, 101-103, 201-203,
(Ref. Fig. 401/TASK 27-54-45-991-001) R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 27-54-45-991-001-A)
**ON A/C ALL
Subtask 27-54-45-941-079
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the warning notice is in position to tell persons not to operate the flap/slat controls.
(3)
Make sure that the warning notice is in position to tell persons not to operate the landing-gear doors.
Subtask 27-54-45-860-065
B. Aircraft Maintenance Configuration
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Make sure that the flaps are fully extended (Ref. TASK 27-50-00-866-008).
(2)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is on the flap/slat control lever on panel 114VU.
(3)
Make sure that the MLG doors are open (Ref. TASK 32-12-00-010-001).
(4)
Make sure that the GROUND LOCK SLEEVE is on the applicable MLG door actuator.
(5)
Make sure that the access platform is in the applicable position.
(6)
Make sure that the applicable access panel is removed:
-
for 6206CM, panel 571AB
-
for 6256CM, panel 671AB.
(7)
Make sure that the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT is installed on the flap torque shaft (Ref. TASK 27-50-00-400-003), outboard of the removed component.
Subtask 27-54-45-865-065
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
1EFF : ALL 1 27-54-45Page 435 1 1 May 01/00R 1 1 1CES 1
4. Procedure
_________ (Ref. Fig. 402/TASK 27-54-45-991-002) CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 27-54-45-420-065
A. Preparation for Installation
CAUTION : DO NOT APPLY MORE THAN ONE TYPE OF LUBRICANT.
_______
GREASE AND ASSEMBLY PASTE DO NOT MIX.
(1)
Use a clean MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026) to clean:
-
the nuts (18) and (21)
-
the bolts (10) and (19)
-
the washers (11) and (23)
-
the cotter pin (22)
-
the flanges of the torque shaft (14) and the plunging joint (15).
(2)
Dry the parts: WARNING : USE A PROTECTIVE EYE SHIELD/GOGGLES WHEN YOU USE COMPRESSED
_______ AIR. DEBRIS AND/OR HIGH PRESSURE AIR CAN DAMAGE YOUR EYES.
WARNING : DO NOT PUT COMPRESSED GAS IN CONTACT WITH YOUR SKIN. THE
_______ GAS CAN GO THROUGH THE SKIN AND MAKE BUBBLES IN THE BLOOD. THIS CONDITION CAN KILL YOU.
(a) Use compressed air to dry the cleaned areas.
(3)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(4)
Do an inspection of the component interface and/or the adjacent area.
(5)
Do one of the steps that follow:
CAUTION : DO NOT APPLY MORE THAN ONE TYPE OF LUBRICANT.
_______
GREASE AND ASSEMBLY PASTE DO NOT MIX.
1EFF : ALL 1 27-54-45Page 436 1 1 May 01/00R 1 1 1CES 1
(a)
Apply a thin layer of COMMON GREASE (Material No. 04-022) to the torque shaft splines.
- or
(b)
Apply a thin layer of COMMON GREASE (Material No. 04-018) to the torque shaft splines.
Subtask 27-54-45-420-052
B. Installation of the Torque Shaft 6206CM(6256CM)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱5(27)
