Torque Shafts - Flap Pwer Transmission
Figure 404A/TASK 27-54-45-991-003-A12 (SHEET 1)
R 1EFF : 062-099, 104-149, 151-199, 204-299, 1 27-54-45Page 446 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Torque Shafts - Flap Pwer Transmission
Figure 404A/TASK 27-54-45-991-003-A22 (SHEET 2)
R 1EFF : 062-099, 104-149, 151-199, 204-299, 1 27-54-45Page 447 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
TASK 27-54-45-400-004 Installation of the Torque Shaft 6208CM(6258CM) WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______ NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice No specific access platform 2.5 m (8 ft. 2 in.) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
1EFF : ALL 1 27-54-45Page 448 1 1 May 01/00R 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 04-018
GENERAL PURPOSE ASSEMBLY PASTE (Ref. 20-31-00)
Material No. 04-022 USA MIL-PRF-81322 GRADE 2
SYNTHE.HYDROCARBON GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
Material No. 15-007 AIB TN 10138 TYPE II GRADE 1 CORROSION PREVENTIVE TEMPORARY PROTECTIVE COMPOUND (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-50-00-000-003 Removal of the Lock-Torque Shaft - Flaps and Slats (98D27504030001) 27-50-00-400-003 Installation of the Lock-Torque Shaft - Flaps and
Slats (98D27504030001)
27-50-00-866-008 Extension of the Flaps on the Ground
27-50-00-866-009 Retraction of the Flaps on the Ground
27-54-00-710-001 Operational Test of the Flap System
**ON A/C 001-049, 051-061, 101-103, 201-203,
27-54-45-991-001 Fig. 401
R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
27-54-45-991-001-A Fig. 401A
**ON A/C 001-049, 051-061, 101-103, 201-203,
27-54-45-991-003 Fig. 404 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
27-54-45-991-003-A Fig. 404A
**ON A/C ALL
3. Job Set-up
__________
**ON A/C 001-049, 051-061, 101-103, 201-203,
(Ref. Fig. 401/TASK 27-54-45-991-001) R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 27-54-45-991-001-A)
**ON A/C ALL
Subtask 27-54-45-941-080
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the warning notice is in position to tell persons not to operate the landing-gear doors.
(3)
Make sure that the warning notice is in position to tell persons not to operate the flap/slat controls.
Subtask 27-54-45-860-066
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊(cè) AMM FLIGHT CONTROLS 飛行操縱5(30)
