(6)
 Install the nuts (10) and TORQUE in a diagonally opposite sequence to between 2.5 and 3.0 m.daN (18.43 and 22.12 lbf.ft).

 (7)
 Do an electrical bonding check between the flap track 1 and the applicable bolt (Ref. TASK 20-28-00-869-002):

 -
FOR 6205CM
 in the LH wing bonding position

 -
FOR 6255CM

R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 27-54-49Page 442 1 1 May 01/05 1 1 1CES 1 in the RH wing bonding position.

 (8)
 Seal the applicable bolt (8), the countersunk washer (7) and the nut

 (10) in the bonding position (Ref. TASK 20-28-00-912-004):
 -
FOR 6205CM
 in the LH wing bonding position

 -
FOR 6255CM
 in the RH wing bonding position.

 (9)
 Apply a thin layer of STRUCTURE PAINTS (Material No. 16-021) when the sealant you applied before is cured.

 (10)
 Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to the remaining bolts (8) and (9), the countersunk washers (7) and the nuts (10).

 (11)
 Install the plunging joint (2) and the universal joint (3) so that the flanges align with the torque shafts (1) and (4).

 (12)
 Install the torque shafts (1) and (4):

 -
FOR 6205CM install 6206CM (Ref. TASK 27-54-45-400-003) and 6204CM (Ref. TASK 27-54-45-400-002)

 -
FOR 6255CM install 6256CM (Ref. TASK 27-54-45-400-003) and 6254CM (Ref. TASK 27-54-45-400-002).

 (13)
 Open the bottom of the two vent covers (12).

 (14)
 Put the 4mm (0.1574 in.) dia. rod through the vent into each hole of the bearing to make sure the holes are not blocked.

 (15)
 Close the bottom vent cover (12).

R **ON A/C 062-099, 106-149, 151-199, 204-299, 401-499,
 Subtask 27-54-49-420-054-B
 D. Installation of the Flap Track 1 Actuator 6205CM(6255CM)
 CAUTION : SUPPORT THE ACTUATOR, WHICH CAN WEIGH UP TO 10.5kg (23.2lbs).
_______ THIS WILL PREVENT DAMAGE TO THE RELATED STRUCTURE AND EQUIPMENT.
R 1EFF : 001-049, 051-099, 101-103, 106-149, 1 27-54-49Page 443 1151-199, 201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 (1)
 To align the actuator:

 (a) Turn the actuator drive, as necessary, and engage the actuator drive in the flap drive lever.

 (2)
 To install the actuator on the flap track:

 (a)
 Put the plunging joint (2) into the torque limiter.

 (b)
 Turn the plunging joint (2) until you can install the actuator assembly and the bolt holes align correctly.

 (c)
 Remove the plunging joint (2).

 (3)
 Put a countersunk washer (7) onto each of the four bolts (8). Make sure that the countersink is adjacent to the head of the bolt.

 (4)
 Install one of the bolts (8) in the applicable bonding position (Ref. TASK 20-28-00-912-004):

 -
FOR 6205CM
 in the LH wing bonding position

 -
FOR 6255CM
 in the RH wing bonding position.

 (5)
 Install the remaining bolts (8) through the actuator and the flap track.

 (6)
 Install the nuts (9) and TORQUE in a diagonally opposite sequence to between 2.5 and 3.0 m.daN (18.43 and 22.12 lbf.ft).

 (7)
 Do an electrical bonding check between the flap track 1 and the applicable bolt (Ref. TASK 20-28-00-869-002):

 -
FOR 6205CM
 in the LH wing bonding position

 -
FOR 6255CM
 in the RH wing bonding position.

 (8)
 Seal the applicable bolt (8), the countersunk washer (7) and the nut

 (9) in the bonding position (Ref. TASK 20-28-00-912-004):
 -
FOR 6205CM
 in the LH wing bonding position

 -
FOR 6255CM
 in the RH wing bonding position.

 (9)
 Apply a thin layer of STRUCTURE PAINTS (Material No. 16-021) when the sealant you applied before is cured.

R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 27-54-49Page 444 1401-499, 1Aug 01/05 1 1 1CES 1

 (10)
 Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to the remaining bolts (8) the countersunk washers (7) and the nuts (9).

 (11)
 Install the plunging joint (2) and the universal joint (3) so that the flanges align with the torque shafts (1) and (4).

 (12)
 Install the torque shafts (1) and (4):
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱5(107)