-
the mating faces of the steady bearing (5) and the structure
-
the shanks of the bolts (4).
(2)
Install the steady bearing (5) on the torque shaft. Attach the steady bearing (5) to the structure with the bolts (4) and the nuts (6).
(3)
Attach the steady bearing (5) to the torque shaft with the bolt (2), the washers (3) and the nut (10).
(4)
TORQUE the nuts (6) to between 0.7 and 0.8 m.daN (61.94 and 70.79 lbf.in).
(5)
TORQUE the nut (10) to between 0.36 and 0.44 m.daN (31.85 and 38.93 lbf.in).
(6)
Safety the nut (10) with a new cotter pin (9).
(7)
Apply a layer of STORAGE PRESERVATION (Material No. 15-007) to:
-
the bolts (2) and (4)
-
the nuts (6) and (10)
-
the washers (3) and the cotter pin (9)
-
the flange of the steady bearing (5).
Subtask 27-54-44-410-051
C. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable torque shaft (1) (Ref. TASK 27-54-45-400-004), (Ref. TASK 27-54-45-400-007):
-
FOR 6207CM
install the torque shaft 6208CM
-
FOR 6257CM
install the torque shaft 6258CM
-
FOR 6213CM
install the torque shaft 6214CM
-
FOR 6263CM
install the torque shaft 6264CM.
1EFF : ALL 1 27-54-44Page 409 1 1 Aug 01/99R 1 1 1CES 1
Subtask 27-54-44-710-050
D. Test
(1) Do an operational test of the flap system (Ref. TASK 27-54-00-710-001).
5. Close-up
________ Subtask 27-54-44-942-050
A. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 27-54-44Page 410 1 1 Aug 01/99R 1 1 1CES 1
TASK 27-54-44-000-002
Removal of the Steady Bearings FIN 6215CM(6265CM)/6219CM(6269CM)/6223CM (6273CM)/6225CM(6275CM)/6229CM(6279CM)/6231CM(6281CM)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______ START A TASK ON OR NEAR: - THE FLIGHT CONTROLS - THE FLIGHT CONTROL SURFACES - THE LANDING GEAR AND THE RELATED DOORS - COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______ GEAR.
R R R R R CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:_______ - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS. - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS. - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific No specific No specific No specific 98D27803500001 circuit breaker(s) safety clip(s)safety barrierswarning noticeaccess platform 2.5 m (8 ft. 2 in.)1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R R R R 27-50-00-400-003 27-50-00-866-009 27-54-45-000-008 27-54-45-000-009 27-54-45-000-010 27-54-45-000-012 27-54-45-000-013 57-51-37-000-004 27-54-44-991-001 Installation of the Lock-Torque Shaft - Flaps and Slats (98D27504030001)Retraction of the Flaps on the Ground Removal of the Torque Shafts 6216CM(6266CM)/6226CM(6276CM)Removal of Torque Shaft 6218CM(6268CM)Removal of the Torque Shaft 6222CM(6272CM)Removal of the Torque Shaft 6228CM(6278CM)Removal of the Torque Shaft 6232CM(6282CM) Removal of the Access Panels 575AB/575BB/575CB/575DB/575EB/575FB/575GB/575HB (675AB/675BB/675CB/675DB/675EB/675FB/675GB/675HB)Fig. 401
3. Job Set-up__________
(Ref. Fig. 401/TASK 27-54-44-991-001)
Subtask 27-54-44-941-053
A. Safety Precautions
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱5(14)
