(a)
Apply SEALANTS (Material No. 09-018) to the bolts (43).
(b)
Install the bolts (43) in the outboard bracket (36) with the bolt heads inboard.
(c)
Apply SEALANTS (Material No. 09-018) or SEALANTS (Material No. 09-019) to the mating face of the anti-rotation plate (42).
(d)
Install the anti-rotation plate (42) on the bolts (43) and loosely install the nuts (41).
(e)
Apply SPECIAL MATERIALS (Material No. 05-064) to the holes of the bearing housings in the brackets (36).
(f)
Apply SEALANTS (Material No. 09-018) to the plain shank and flange of the bearing housing (34).
(g)
Install the bearing housing (34) in the outboard bracket (36) and tighten the nuts (41).
(h)
Apply COMMON GREASE (Material No. 04-022) to the ring nut (40).
(i)
Install the ring nut (40) on the bearing housing (34).
(j)
Torque the ring nut (40) with the SPANNER-FLAP LEVER TRACKS 2 AND 3 (98D27504028000) to between 1.4 and 1.5 m.daN (10.32 and 11.06 lbf.ft).
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 27-54-55Page 437 1 1 Aug 01/05 1 1 1CES 1
(k)
If necessary, drill a 2.5 mm (0.10 in.) hole for the cotter pin
(37)
in an applicable position on the bearing housing (34). Remove all unwanted material from the area.
(l)
Safety the ring nut (40) with a new cotter-pin (37).
(m)
Apply COMMON GREASE (Material No. 04-022) to the bearing surfaces of the lever (28).
(n)
Turn the lever (28) through 90 deg. and install it in the bearing housing (34).
(o)
Install the bearing housing (26), the bolt (25) and the nut (44).
(p)
Apply COMMON GREASE (Material No. 04-022) to the retention plate
(35)
and to the bolt (27).
(q)
Install the retention plate (35), the bolt (27) and the nut (39).
(r)
TORQUE the nut (39) to between 1.4 and 1.5 m.daN (10.32 and 11.06 lbf.ft).
(s)
Manually operate the lever (28) and make sure that it moves freely.
(t)
Safety the nut (39) with the new cotter pin (38).
(u)
Remove the adjustable strut.
(2) At the track 1 position: (Ref. Fig. 401/TASK 27-54-55-991-001)
(a)
Install the bushes (12) on the lever (1).
(b)
Connect the lever (1) to the flap link arm (5) as follows:
1_ Put and hold the packers (11) and (13) in position on the
lever (1).
2_ Put the lever (1) in position on the flap link arm (5).
3_ Install the bolt (10), the washer (4) and the nut (3).
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 27-54-55Page 438 1 1 Aug 01/05 1 1 1CES 1
(3)
At the track 2 position:
(a) Connect the lever (28) to the flap link arm (32) as follows:
(4)
Do a check of the flap rigged position (Ref. TASK 27-51-00-820-003).
(5)
At the track 1 position:
(a)
TORQUE the nut (3) to between 1.6 and 1.8 m.daN (11.79 and 13.27 lbf.ft) and safety with a new cotter pin (2).
(b)
Install the indicator pin (9), the indicator plate (8), the washers (6) and the bolts (7).
(c)
TORQUE the bolts (7) to between 0.15 and 0.17 m.daN (13.27 and
15.04 lbf.in).
(6)
At the track 2 position:
(a) TORQUE the nut (31) to between 10 and 12 m.daN (73.74 and 88.49 lbf.ft) and safety with a new cotter-pin (30).
(7)
At tracks 1 and 2:
(a)
Apply STORAGE PRESERVATION (Material No. 15-007) to the bolts
(10)
and (33) and the nuts (3) and (31) after assembly.
(8)
Install the Flap Track 2 Actuator 6211CM(6261CM) (Ref. TASK 27-54-49-400-002).
(9)
Remove the locking tools LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT from the torque shaft outboard of the Track 2 actuator (Ref. TASK 27-50-00-000-003).
1_ Apply SPECIAL MATERIALS (Material No. 05-002) to the bolt (33)
and the nut (31).
2_ Install the bolt (33), the washer (29) and the nut (31).
(10) Remove the hoisting sling (Ref. TASK 27-50-00-000-002).
R 1EFF : 001-049, 051-061, 101-103, 201-203, 1 27-54-55Page 439 1 1 Aug 01/05 1 1 1CES 1
R **ON A/C 062-099, 104-105, 151-158, 204-210,
Subtask 27-54-55-420-053-A R B. Installation of the Flap-Actuator Lever Assembly - Track 1 WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱5(174)
