(6)
If the APPU and FPPU angles are not within the specified limit, do these steps:
(a)
Disconnect the APPU and adjust the APPU input shaft.
(b)
Do again step (6)(a) until the APPU angles are in the specified limits in relation to the FPPU angles.
SFCC 1
PPU DATE (DEG)
DATE:XXX XX UTC:XXXX
LH APPU FPPU RH APPU
***.* ***.* ***.*
***HEX ***HEX ***HEX ***
OTHER SFCC
LH APPU FPPU RH APPU
***.* ***.* ***.* ***
***HEX ***HEX ***HEX
<RETURN PRINT>
Table 1 PPU DATA (DEG) displayed on the MCDU at the flap position FULL
Subtask 27-54-49-860-061-A
H. Aircraft Maintenance Configuration
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Retract the No. 4 and the No. 5 spoilers (Ref. TASK 27-60-00-866-002).
(3)
Remove the warning notice(s).
(4)
Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever in the cockpit.
Subtask 27-54-49-865-065
J. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 27-54-49-710-053
K. Test
(1) Do an operational test of the flaps (Ref. TASK 27-54-00-710-001).
5. Close-up
________ Subtask 27-54-49-410-060
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the applicable access panels:
-for the left wing, install 573BB, 575CB, 575EB, 575FB, 575GB
-for the right wing, install 673BB, 675CB, 675EB, 675FB, 675GB. Subtask 27-54-49-942-057
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
CONTROL UNIT - POWER (PCU) (FLAPS) (6201CM) - REMOVAL/INSTALLATION
__________________________________________________________________
TASK 27-54-51-000-001
Removal of the Power Control Unit 6201CM of the Flap System
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______
CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific blanking plugs
No specific circuit breaker(s) safety clip(s)
No specific container
No specific warning notice
No specific access platform 2.20 m (7 ft. 3 in.)
No specific access platform 3.0 m (9 ft. 10 in.)
R No specific 1 ACCESS PLATFORM 3M (10 FT) R No specific 1 CONTAINER 5 L(1 1/2 USGAL) R No specific 1 WARNING NOTICE
98D27504005000 2 PIN RIGGING-FLAPS (TRACK 1)
R 98D27504006000 2 PIN RIGGING FLAPS 98D27504030001 2 LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-00-00-480-002 Installation of the Flap/Slat Control-Lever Locking Tool (98D27803000000) 27-50-00-400-003 Installation of the Lock-Torque Shaft - Flaps and
Slats (98D27504030001) 27-50-00-866-009 Retraction of the Flaps on the Ground 29-00-00-864-001 Put the Related Hydraulic System in the Depressurized
Configuration before Maintenance Action 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 31-32-00-860-006 Procedure to Get Access to the SYSTEM REPORT/TEST
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱5(133)
