曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
CAUTION: MAKE SURE THE INBOARD FAN DUCT COWL AND THE INBOARD AND OUTBOARD
THRUST REVERSERS ARE CLOSED OR REMOVED BEFORE YOU EXTEND THE
LEADING EDGE FLAPS AND SLATS. THERE IS NOT SUFFICIENT CLEARANCE FOR
THE FLAPS AND SLATS TO EXTEND IF THE INBOARD FAN DUCT COWL AND THE
INBOARD AND OUTBOARD THRUST REVERSERS ARE IN THE OPEN POSITION. THIS
CAN CAUSE DAMAGE TO EQUIPMENT.
(5) Move the flap control lever to the 10-unit position to move the leading edge slats to the full
extend position.
SUBTASK 27-81-41-480-002
WARNING: MAKE SURE TO INSTALL THE LEADING EDGE SLAT ACTUATOR LOCKOUT SET TO
PREVENT ACCIDENTAL OPERATION OF THE LEADING EDGE SLATS. THE LEADING
EDGE SLATS CAN MOVE QUICKLY. THIS CAN CAUSE INJURY TO PERSONS AND
DAMAGE TO EQUIPMENT.
(6) Install the lockout set, SPL-1734 on the adjacent leading edge slats. To install the lockout set, do
this task: Leading Edge Flap and Slat Locks Installation, TASK 27-81-00-480-801.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-41
Page 403
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-81-41-860-012
(7) Move the flap control lever to the 1-unit position to move the leading edge slat to the extend
position.
NOTE: If the slat is in the full extend position, the actuator [1] will be preloaded against the slat.
F. Leading Edge Slat Actuator Removal
SUBTASK 27-81-41-020-002
(1) Remove the slat actuator door [3] from the slat actuator assembly [2]:
(a) Remove the bolts [14], washers [15], washers [16] and nuts [17] that attach the slat actuator
door [3] and clamp [52] to the slat actuator assembly [2].
(b) Remove the bolts [4], washers [5] and nuts [6] that attach the slat actuator door [3] and the
bracket [32] to the slat actuator assembly [2].
(c) Remove the slat actuator door [3].
(d) Temporarily install the bolts [4], washers [5] and nuts [6] to attach the bracket [32] to the
slat actuator assembly [2].
SUBTASK 27-81-41-860-008
(2) To remove power from hydraulic system B, do this task: Hydraulic System A or B Power
Removal, TASK 29-11-00-860-805.
SUBTASK 27-81-41-020-003
(3) Remove the dropout links [7]:
(a) Remove the pin [13], nuts [12], washers [11], washers [9], bolts [8] and bushings [10].
(b) Remove the dropout links [7].
SUBTASK 27-81-41-020-004
(4) Disconnect the slat actuator assembly [2] from the leading edge slat [1]:
(a) Remove the bolt retainer [23] from the leading edge slat [1]:
1) Remove the bolts [21] and washers [22] that attach the bolt retainer [23] to the leading
edge slat [1].
2) Remove the bolt retainer [23] from the leading edge slat [1].
(b) Remove the nut [19], washer [20], washer [24], bolt [25] and bushing [18].
SUBTASK 27-81-41-980-001
(5) Manually move the leading edge slat [1] to the full extend position while you hold the slat
actuator assembly [2].
SUBTASK 27-81-41-980-002
(6) Let the slat actuator assembly [2] hang from the support fitting [46].
SUBTASK 27-81-41-020-005
(7) Remove the slat actuator assembly [2]:
(a) Disconnect the hydraulic lines [29], [30] or [53], [54] with [40] and [41]:
NOTE: The hydraulic lines [29], [30] or [53], [54] with [40] and [41], bracket [32] and
clamps [26] and [36] are removed from the airplane with the slat actuator
assembly [2].
1) Disconnect the hydraulic lines [29], [30] or [53], [54] with [40], [41] from the swivels [31].
2) Install caps on the swivels [31].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-41
Page 404
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
3) Install plugs in the open ends of the hydraulic lines [29], [30] or [53], [54] with [40] and
[41].
(b) Remove the nut [47] and washer [48] from the bolt [44].
(c) Hold the slat actuator assembly [2] while you remove the bolt [44], washer [45] and bushing
[43].
(d) Remove the slat actuator assembly [2] from the airplane.
SUBTASK 27-81-41-020-006
(8) If it is necessary, remove the hydraulic lines [29], [30] or [53], [54] with [40], [41] and bracket [32]
from the slat actuator assembly [2]:
(a) Disconnect the hydraulic lines [29], [30] or [53], [54] with [40], [41] from the slat actuator
assembly [2].
(b) Remove the nuts [6], washers [5] and bolts [4] that attach the bracket [32] to the slat
actuator assembly [2].
(c) On slat 1, remove the nut [28] and bolt [27] and the clamps [26] that attach hydraulic lines
[29] and [30] to the slat actuator assembly [2].
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊7 AIRCRAFT MAINTENANCE MANUA(83)