曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

2) Add or remove shim [87] as it is necessary until the slat fairs with the adjacent slat.
NOTE: Add or remove only a minimum amount of shim necessary for the slat upstop
to touch the stop pad. To adjust each stop pad, add or subtract in any
combination of 0.0100, 0.0200, 0.0400,and 0.0630 inch thick solid shims. The
total permitted shim thickness is 0.0000 to 0.1280 inch and must be such that
the slat flex skin keeps solid contact with the fixed leading edge.
3) Install the bolts [89], nuts [86] and retainers [85].
(e) Adjust the aft support of the auxiliary track [72];
1) Loosen the upper aft aux track locking bolt [91].
a) Loosen the nut [90].
2) Loosen the jam nut [82].
3) Loosen the nut [80] on the locking bolt [79].
4) Turn the adjusting nut [81] until the gap between the slat and the fixed leading edge is
0.0020 -0.0000/+0.0060 inch (0.05 -0.00/+0.15 millimeters).
NOTE: Measure the gap at the highest point, within 2.00 inches (50.8 millimeters) on
either side of the each auxiliary track centerline. Measure the gap to a depth
of 0.4000-0.6000 inch (10.16-15.24 millimeters).
5) Temporarily tighten the locking bolt [79].
6) Temporarily tighten the jam nut [82].
7) Temporarily tighen the upper aft aux track locking bolt [91].
(f) Measure and calculate the weighted average misfair.
1) Measure the misfair at six locations for each specified gap (Table 502);
NOTE: There will be a total of 30 locations on each wing that you will need to
measure.
a) The gap between all adjacent slat ends
b) The gap between the outboard end of slats 1 and 8 and the adjacent fixed leading
edge
c) The gap between the inboard end of slats 4 and 5 and the adjacent fixed leading
edge.
Table 502/27-81-00-993-811
Point Location Value
F1 Outbd slat 1/8
F2 Outbd slat 1/8
F3 Outbd slat 1/8
F4 Outbd slat 1/8
F5 Outbd slat 1/8
F6 Outbd slat 1/8
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-00
Page 525
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(Continued)
Point Location Value
F11 Inbd slat 1/8
F12 Inbd slat 1/8
F13 Inbd slat 1/8
F14 Inbd slat 1/8
F15 Inbd slat 1/8
F16 Inbd slat 1/8
F21 Inbd slat 2/7
F22 Inbd slat 2/7
F23 Inbd slat 2/7
F24 Inbd slat 2/7
F25 Inbd slat 2/7
F26 Inbd slat 2/7
F31 Inbd slat 3/6
F32 Inbd slat 3/6
F33 Inbd slat 3/6
F34 Inbd slat 3/6
F35 Inbd slat 3/6
F36 Inbd slat 3/6
F41 Inbd slat 4/5
F42 Inbd slat 4/5
F43 Inbd slat 4/5
F44 Inbd slat 4/5
F45 Inbd slat 4/5
F46 Inbd slat 4/5
2) Multiply all negative fair measurements by -0.5.
3) Add all the misfair values (positive and negative misfairs).
4) Divide the total misfair value by 6.
5) Make sure the result is 0.0000-0.0500 inch (0.00-1.27 millimeters).
(g) Make sure the slat endstops touch the horizontal and vertical stop pads.
(h) If the slat endstops do not touch the horizontal and vertical stop pads, adjust the stop pad:
1) Remove the retainers [85], nuts [86] and bolts [89].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-81-00
Page 526
Feb 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
2) Add or remove shim [87] as it is necessary until the slat fairs with the adjacent slat.
NOTE: Add or remove only a minimum amount of shim necessary for the slat upstop
to touch the stop pad. To adjust each stop pad, add or subtract in any
combination of 0.0100, 0.0200, 0.0400,and 0.0630 inch thick solid shims. The
total permitted shim thickness is 0.0000 to 0.1280 inch and must be such that
the slat flex skin keeps solid contact with the fixed leading edge.
3) Install the bolts [89], nuts [86] and retainers [85].
SUBTASK 27-81-00-820-009
(3) Do the final adjustment of the leading edge slat in the (intermediate) extend position:
WARNING: MAKE SURE PERSONS AND EQUIPMENT ARE CLEAR OF THE LEADING EDGE
FLAPS AND SLATS AND THE TRAILING EDGE FLAPS. THE FLAPS AND SLATS
CAN MOVE QUICKLY. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO
EQUIPMENT.
(a) To extend the leading edge slat to the (intermediate) extend (1-unit detent) position, do this
task: Leading Edge Flaps and Slats Extension, TASK 27-81-00-860-803.
(b) Align the noses of the slats to get a mismatch of 0.0000 to 0.0600 inch between adjacent
slats.
(c) Make sure the detent roller touch the root of each detent arm.
(d) Make sure the gap between the detent roller and the aft surface of the cam plate is 0.0000 to
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊7 AIRCRAFT MAINTENANCE MANUA(49)