曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(1) Install the cable [1]:
(a) Install the screws [26], washers [27], and clamps [25] to attach the cable [1] to the airplane
structure.
(b) Install the screws [29], washers [30], and clamps [28] to attach the cable [1] to the airplane
structure.
(c) Install the screws [32], washers [33], and clamps [31] to attach the cable [1] to the airplane
structure.
(d) To install the center door [34], do this task: Main Landing Gear Inner Door Installation,
TASK 32-13-11-420-804.
(e) Install the bolts [19] and washers [18] to attach the retainer [17] to the nutplates [16].
(f) Install the nut [23], washer [22], and bolt [21] in the retainer [19].
(g) Install the nut [15], washer [14], washer [13], and bolt [12] that attach the cable [1] to the
airplane structure.
(h) Install the lockwire, G01912 to the bolts [19], and bolt [21].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-51
Page 411
Jun 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(i) Install the clip assembly [8].
(j) Install the bolts [11] and washers [10] to attach the retainer [9] to the clip assembly [8].
SUBTASK 27-62-51-420-006
(2) To install the lower slider, do this task: Lower Slider Installation, TASK 27-62-51-400-802.
SUBTASK 27-62-51-720-002
(3) Do this task: Ground Spoiler Interlock Valve Adjustment, TASK 27-62-00-820-803 or this task :
Ground Spoiler Interlock Valve Adjustment (Alternate Method), TASK 27-62-00-820-811.
SUBTASK 27-62-51-860-008
(4) Do this task: Put the Speed Brake Systems A and B Back to the Condition Before the
Pressure Removal, TASK 27-62-00-840-802.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-51
Page 412
Jun 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
GROUND SPOILER INTERLOCK VALVE - REMOVAL/INSTALLATION
1. General
A. This procedure has these tasks:
(1) A removal of the ground spoiler interlock valve.
(2) An installation of the ground spoiler interlock valve.
(3) A removal of the ground spoiler interlock valve proximity sensor.
(4) An installation of the ground spoiler interlock valve proximity sensor.
(5) A removal of the ground spoiler interlock valve pressure switch.
(6) An installation of the ground spoiler interlock valve pressure switch.
(7) In this procedure the ground spoiler interlock valve is referred to as the "valve".
TASK 27-62-61-000-801
2. Ground Spoiler Interlock Valve Removal
(Figure 401)
A. References
Reference Title
27-62-00-800-802 Remove Pressure from the Speed Brake Hydraulic Systems A and B
(P/B 201)
B. Tools/Equipment
Reference Description
STD-1110 Container - Hydraulic Fluid Resistant, 5 Gallon (19 Liters)
C. Location Zones
Zone Area
134 Main Landing Gear Wheel Well, Body Station 663.75 to Body Station
727.00 - Right
D. Prepare for the Removal
SUBTASK 27-62-61-860-001
(1) Do this task: Remove Pressure from the Speed Brake Hydraulic Systems A and B,
TASK 27-62-00-800-802.
E. Ground Spoiler Interlock Valve Removal
SUBTASK 27-62-61-020-001
(1) Remove the nut [10], washer [9], washer [8] and bolt [7] that attach the push-pull cable to the
valve input lever [11].
NOTE: The valve input lever [11] is part of the valve [1] assembly. Do not remove the valve
input lever [11] from the valve [1].
SUBTASK 27-62-61-020-002
(2) Disconnect the electrical connector [5] and the electrical connector [2].
SUBTASK 27-62-61-020-003
(3) Disconnect the hydraulic lines [12] from the valve [1]:
(a) Put a 5 gallon (19 liters) hydraulic fluid resistant container, STD-1110 below the valve [1] to
catch the hydraulic fluid.
(b) Disconnect the hydraulic lines [12] from the valve [1].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-61
Page 401
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(c) Install the plugs in the hydraulic lines [12].
SUBTASK 27-62-61-020-004
(4) Remove the bolts [3] and washers [4] that attach the valve [1] to the structure.
SUBTASK 27-62-61-020-005
(5) Remove the valve [1] from the airplane.
SUBTASK 27-62-61-020-006
(6) Remove the reducers [13] and the packings [14] from the valve [1] ports.
SUBTASK 27-62-61-480-001
(7) Install caps in the hydraulic ports of the valve [1].
------------------------- END OF TASK ---------------------------
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊7 AIRCRAFT MAINTENANCE MANUA(17)