曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

3. Outboard Ground Spoiler Installation
(Figure 401)
A. References
Reference Title
27-62-00-800-801 Speed Brake Hydraulic Systems A and B Pressurization (P/B 201)
27-62-00-820-804 Ground Spoiler Adjustment (P/B 501)
27-62-00-840-801 Put the Speed Brake Hydraulic systems A and B Back to the
Condition Before the Pressurization (P/B 201)
B. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
SPL-1743 Set - Ground Lock, Outboard Spoiler Actuators
(Part #: C27001-35, Supplier: 81205, A/P Effectivity: 737-600, -700,
-700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
C. Consumable Materials
Reference Description Specification
D00633 Grease - Aircraft General Purpose BMS3-33
D. Expendables/Parts
AMM Item Description AIPC Reference AIPC Effectivity
9 Pin 27-31-41-01-110 GUN ALL
57-42-00-04-010 GUN 008-099, 101-122
16 Pin 57-42-00-04-055 GUN 008-099, 101-122
24 Pin 27-62-94-01-125 GUN ALL
25 Actuator assembly 27-62-94-01-155 GUN ALL
31 Pin 57-42-00-04-055 GUN 008-099, 101-122
39 Pin 27-31-41-01-110 GUN ALL
57-42-00-04-010 GUN 008-099, 101-122
E. Location Zones
Zone Area
210 Subzone - Control Compartment - Body Station 178.00 to Body
Station 259.50
566 Left Wing - Spoiler No. 1
666 Right Wing - Spoiler No. 12
F. Outboard Ground Spoiler Installation
SUBTASK 27-62-91-420-001
(1) Install the outboard ground spoiler [1]:
(a) Put the outboard ground spoiler [1] in its position on the airplane.
(b) Install the bolt [34] with the head inboard, washer [35], bushing [36], washer [37], nut [38],
and pin [39] in the inboard hinge.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-91
Page 407
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(c) Install the bolt [26] with the head inboard, washer [27], bushing [28], washer [29], nut [30],
and pin [31] in the center right hinge fitting.
(d) Install the bolt [11] with the head outboard, washer [12], bushing [13], washer [14], nut [15],
and pin [16] in the center left hinge fitting.
(e) Install the bolt [4] with the head outboard, washer [5], bushing [6], washer [7], nut [8], and
pin [9] in the outboard hinge fitting.
(f) Install washers [3] and nut [2] and connect the bonding jumper [10] to the outboard ground
spoiler [1].
(g) Install washers [33] and nut [32] and connect the bonding jumper [40] to the outboard
ground spoiler [1].
SUBTASK 27-62-91-980-001
(2) Move the outboard ground spoiler [1] through its full travel.
(a) Make sure the outboard ground spoiler [1] moves freely.
SUBTASK 27-62-91-420-002
(3) Install the bolt [18] that attaches the rod end for the spoiler actuator assembly [25] to the
outboard ground spoiler [1].
(a) Apply a layer of grease, D00633 to the bolt [18].
(b) Install the bolt [18] with its head outboard.
(c) Install the washer [22], bushing [20], bushing [21], washer [19] and the nut [23] on the bolt
[18].
(d) Tighten the nut [23] to 660-780 pound-inches (74.6-88.1 newton-meters).
(e) Install the pin [24].
(f) Apply grease, D00633 to the bolt [18], washer [19], bushing [20], bushing [21], washer [22],
nut [23], and pin [24].
SUBTASK 27-62-91-860-007
(4) Make sure hydraulic power is not on.
SUBTASK 27-62-91-080-001
CAUTION: INSPECT THE LOCKWIRE AND LOCKING KEY FOR DAMAGE AFTER THE SPOILER
TOOL IS REMOVED.
(5) Remove set, SPL-1743.
SUBTASK 27-62-91-860-008
WARNING: MAKE SURE THAT PERSONS AND EQUIPMENT ARE CLEAR OF ALL CONTROL
SURFACES BEFORE YOU SUPPLY HYDRAULIC POWER. AILERONS, RUDDERS,
ELEVATORS, FLAPS, SLATS, SPOILERS, LANDING GEAR, AND THRUST REVERSERS
CAN MOVE QUICKLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN CAUSE
INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(6) Do this task: Speed Brake Hydraulic Systems A and B Pressurization,
TASK 27-62-00-800-801.
SUBTASK 27-62-91-860-009
(7) Move the speed brake lever to the DOWN position to lower the spoilers.
SUBTASK 27-62-91-860-010
(8) Do this task: Put the Speed Brake Hydraulic systems A and B Back to the Condition Before
the Pressurization, TASK 27-62-00-840-801.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-62-91
Page 408
Jun 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊7 AIRCRAFT MAINTENANCE MANUA(28)