曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

b) Open this folder. There is a subfolder called NetDir. Right click, Properties, and select the “sharing”
tab or option. Now allow sharing over the network, and set the share name to NetDir. Make sure
you have selected full read/right access and that it is not a private folder. Click OK and close.
c) Now run the CDU program. It will detect automatically the NetDir and should set the software for
its use.
Project Magenta Revision: 12 March-08
10
d) To check that everything is working, download and install the latest version of the pmFileCheck
program from the Project Magenta website. When you run it, with the CDU software running as
well, and a connection to MSFS via wideclient, it will produce a test report indicating any problems.
Step 6 Sharing In General
Check that there is no network or firewall restrictions between folders that need full sharing / read and
write access.
Typical symptoms of incorrectly set NetDir:
• Red display “FAIL” in the CDU (bottom right of graphic or on your CDU hardware)
• Receiving a “Network Error” message in the CDU scratch pad.
• Seeing no vspeed (once set), flaps, flight plan in the PFD, ND and EICAS respectively when running
the Glass Cockpit programs.
If any of the above occur, something is not correctly set. Check:
• File & Printer Sharing Services installed and active for the network
• All computers “see” each other and can exchange files
• You have created and shared the NetDir folder with full read/write access
• When looking at the cdu.ini file (using Notepad text editor) you can see an entry in the file called:
NetDir=\\machinename\NetDir
If the entry looks something like this:
NetDir=c:\cdu\NetDir
Then this is incorrect and the folder is not being shared across the network.
Optimization
Here is a list of tips to make sure your network runs as fast as possible... this mostly applies to XP systems.
• avoid any "Auto" settings in the network "LAN Settings" for the Link Speed / Duplex, e.g. use "100
Full Duplex" rather than "Auto"
• Set the "receive Buffer" of your network card as high as possible
• Disable the "Allow Indexing Service to index this disk..." in your "Local Disk Properties", as it really
slows down network file transfer
• Limit your FS frame rate, avoid "unlimited" 30 FPS should be enough for most, use 50 fps if you
must and your hardware can handle it. High or Unlimited settings will leave WideServer very little
time to process network traffic and will result in pauses in the connected programs.
• turn off automatic updates
• assign an IP address for every machine, do not use automatic settings for that
• disable network authentication IEEE 802
• if you have control, turn off system restore disable automatic synchronise internet time
Project Magenta Revision: 12 March-08
11
A possible side effect of using TCP/IP is “stutters / pauses” across the network. If this is observed on your
system, you will have to assign a static IP address rather than just simply using a computer name in the
wideclient.ini file setting. Refer to the WideFS documents for further information on setting different
network protocols.
Other Required Shares
Other required shares for our programs to communicate properly with FS and display or save FS flight
plans:
- share the FS folder with read/write access
- for FS9 and FSX share the \My Documents\Flight Simulator Files folder with the share name FSPLANS, if
using XP make sure that this folder is not private
Note: share name does not mean renaming an existing folder, this is the name given to the share that you
are creating
Project Magenta Revision: 12 March-08
12
pmFileCheck Tool
As mentioned before, pmFileCheck is a very helpful tool to check everything is OK with your PM setup. You
can find it in the main folder of practically all programs (Glass Cockpit, FMC, IFR Panels etc.)
It will check the connection to flight simulator and its frame rate, show the detected WideFS versions,
inspect the NetDir settings and so forth. It will help you identify any problems and will suggest solutions
should any issues appear to be the case. It is possible to copy the result to the clipboard and send it to PM
support should you need any help.
pmFileCheck Build 36
Opening Connections
Local Path: C:\NonSim\pmFileCheck
Checking Computer and User Name
Local Computer Name: FSN
Local User Name: Owner
FSUIPC/WideFS found!
FSUIPC Version 3.53
WideServer Version 6.51
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料13(3)