曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

• Colour Depth 16mb and above (ideally 32mb) 1024x680 and above
• WideFS & FSUIPC (Registered full version)
• Network PC to MSFS
• Windows Operating System Win98 and above
• MSFS
• Single or Twin Engine Flight model of your choosing
• Default MSFS panels
The GAIFR panel has been designed to operate at extremely high screen resolutions as well as lower
resolutions. If using the very high resolutions, then system spec may need to be increased considerably.
GAIFR Introduction
The General Aviation Instrument Flight Rules (GAIFR) panel is aimed at instrument rated pilots wishing to
maintain proficiency or for pilots undergoing instrument flight Training within a flight school. The panel of
course can be used for VFR flight as well.
The panel has been designed with a basic set of instruments which should be sufficient for most IFR
procedures. Actual aircraft instruments may differ slightly due to the various manufacturers. The quality
and resolution of the instruments is such that pilots should be able to fly accurate approaches, radials and
all the necessary instrument procedures with a high degree of accuracy required for this type of training.
Advanced features to aid in training have
been implemented such as failure modes.
This will enable pilots to practice typical
flight procedures like simulated Gyro
rundowns or electrical and Pitot/Static Air
failures. Other useful direct options are a
pause mode and simulation rate
alteration. There are short cut keys /
commands for these so they can be
operated either via keyboard, mouse or
by third party hardware professional
training hardware, such as avionics
stacks, dampened control yokes and
throttle systems.
The AP is a basic system found on many
GA aircraft with a HDG hold facility linked
to the HDG BUG on the HI and a current
Altitude hold mode. This will enable the practicing pilot to drop work loads as and when required and focus
on specific learning tasks.
Project Magenta Revision: 12 March-08
63
MSFS simulator must be installed to use this software. There are various options with regard to this
discussed in the following pages. It is also assumed that the necessary hardware you intend to use has
been installed, whether this is a simple Joystick with throttle control or more advanced professional training
systems.
The GAIFR software from Project Magenta must be downloaded and installed either on the computer you
are running MSFS on or a second Client computer (recommended).
When you run the GAIFR software for the first time it will request a registration code. You have to e-mail
Project Magenta the code that the software generates in the top half of the registration box, (the
instructions will be found in your original Order Confirmation e-mail). Once we have this code we then send
you an Activation Code and the software is activated – but not ready to use just yet. Please read further for
how to set-up your systems so that the software can communicate with MSFS.
Project Magenta Revision: 12 March-08
64
Step 1 GAIFR Network Set-up
The main advantage of a Networked solution when running the GAIFR panel is that you can maintain an
outside visual environment without any loss of computer performance. This solution is ideal for any
individual or training organization who decides to have two computers running together with two monitors.
The principle is very simple. One computer usually the SERVER runs MSFS, and the second computer, the
CLIENT runs the GAIFR software. In this way, you can run MSFS in Full Screen Mode (just the full scenery
screen view) and have the flight instruments displayed in very high resolution on the second display driven
by the second computer (CLIENT). The two computers and simulation programs are connected together via
a network and a program called WideFS.
For networking you will require that each of your PC’s has a Network adaptor card. These are usually PCI
10/100base Ethernet cards. Once these are installed in each machine (as per manufacturers guide lines)
you need either to connect them together via a Hub (or switch), or the cheapest solution would be a simple
crossover Cable (if only two computers are to be connected). Please note that some operating systems will
not work well together using a crossover cable (e.g. XP and Win2000).
For new Network installations, after installing the Network cards you have to establish that the network is
able to see all the computers.
GAIFR Workgroups
Both computers must have the same Workgroup. This can be set via the Network Icon under the Windows
Control Panel. By clicking on the Identification tab you can enter the name of the Workgroup, for example,
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料13(20)