曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Section V
Operations
5-4 2423sv602
Change 1
To adjust screen brightness:
1. Press the ON/OFF key again to access the dimming control
window.
2. Hold the BRIGHT or DIM line select keys as necessary to
change screen intensity.
3. Select the CANCEL line select key to return to the Initialization
page.
To adjust display/key alignment:
1. Press the DISPLAY line select key to access the display option
window.
2. Press the UP or DOWN line select keys as necessary to align
display arrows with line select keys.
3. Select the CANCEL line select key to return to previous display.
Section V
Operations
2423sv602 5-5
Change 1
To access VIDEO mode:
NOTE: VIDEO option is only available with certain CDU part
numbers.
1. With the dimming control window displayed, press the DISPLAY
line select key to access the display option window.
2. Press the VIDEO line select key to access the video mode.
Active video source will be displayed.
3. Press any key to exit video mode.
INITIALIZATION
The Initialization page automatically appears at the end of the self
test if the self test was passed without a fault, which would preclude
use of the system.
Typically, the data shown on the Initialization page will be correct, as
the position, date and time shown will be from the GPS (as indicated
by <GPS> in the Ident field after the GPS transitions to NAV mode).
For non-GPS installations, position will be the same as when the
system was last powered down.
1. Press the ACCEPT line select key to accept the data.
Section V
Operations
5-6 2423sv602
Change 1
If data shown is not correct:
3. Use the line select keys to place the cursor over the fields to be
corrected or changed and proceed as follows:
a) POS - Entering an ID (identifier) into this field will
automatically update the INITIAL POS coordinates. Input
the identifier using the LIST function or type the identifier into
the cursor. With the IDENT entry field empty, pressing the
ENTER key will access the
DEFINE POS page - Initialization data can be entered on this
page in several different ways:
i) Reference Wpt/Radial/Distance - The cursor will be
defaulted to the REF WPT field. Enter a reference
identifier, radial and distance. The resulting lat/long
will be shown.
ii) Latitude/Longitude - Press line select key to position
cursor over latitude field. Enter latitude and
longitude as required. N/S and E/W may be toggled
with the ± key.
iii) GPS Position - If the GPS in NAV mode, line select
key [3R] will indicate GPS POS. Pressing this key
will load GPS position into the latitude/longitude
field. GPS POS is not displayed if a reference
waypoint has been entered.
Section V
Operations
2423sv602 5-7
Change 1
b) DATE - Enter the date at the zero meridian numerically
(DDMMYY).
c) UTC - Enter Coordinated Universal Time (hours:minutes).
Press the ACCEPT line select key to accept the initialization data.
All data will turn green; indicating that initialization is complete.
NOTE: In the event it is noted that one of the entries on the
initialization page was entered in error, (and prior to
leaving the initialization page) the erroneous field can be
easily corrected as described above by repeating the
appropriate steps.
Section V
Operations
5-8 2423sv602
Change 1
Crossfill Options
Three types of data can be crossfilled from one FMS to the other
FMS(s): initialization, flight plan and fuel data. These can either be
crossfilled separately or all at once. Crossfill can be configured at
installation to either PULL data to the requesting FMS or PUSH data
to the receiving FMS. The default crossfill configuration is PULL.
Master Crossfill
The MSTR XFILL prompt will only appear if the master crossfill
option is configured, when there are two or more FMSs installed and
all data (initialization, fuel and flight plan) on the other system is
valid.
The MSTR XFILL function will crossfill flight plan, fuel and
initialization data to or from the other FMS. During crossfill, a graphic
screen labeled CROSSFILL RECEIVE IN PROGRESS will be
displayed on the appropriate FMS.
The MSTR XFILL prompt is available on either the Initialization Page
or the DATA 1/4 page.
Using MSTR XFILL is simply a matter of entering all initialization,
fuel and flight plan data on one FMS, and then selecting MSTR
XFILL on the appropriate FMS(s), then pressing the ACCEPT line
select key.
Crossfill
The XFILL prompt will appear in both single and multiple FMS
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：龐巴迪挑戰者手冊10(62)