曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 NOTE: Door will not move, as the flex cables are disconnected.
____
 CAUTION: DO NOT OPERATE THE NOSE CARGO DOOR BEFORE THE LINEAR
_______ ACTUATORS ARE ADJUSTED. THE DRIVE SYSTEM CAN BE DAMAGED IF YOU OPERATE THE DOOR BEFORE THE LINEAR ACTUATORS ARE ADJUSTED.
 (f)  Manually adjust the length of the linear actuators until rig pin ND-2 fits freely in the rig pin hole in the aft end of the actuator shafts (AMM 52-31-00/501).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-31-02
 ALL  ú ú 02 Page 503 ú Feb 18/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (g)  
Connect the flexible drive shafts on the linear actuators.

 (h)  
Remove the DO-NOT-CLOSE tags and close this circuit breaker:

 1)  On the Nose Cargo Door Power Panel H122: a) PULL UP CAM
 S 865-012
 (8)  
Hold the control switches to fully close and latch the nose cargo door.

 G.  
Put the Airplane Back To Its Usual Condition

 S 865-013
 (1)  
Make sure the door is fully closed, latched and locked.

 S 865-014

 (2)  
Remove the electrical power, if it is not necessary.

 (3)  
Remove the safety barrier across the door opening.

 S 095-015
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-31-02
 ALL  ú ú 02 Page 504 ú Feb 10/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 NOSE CARGO DOOR LINEAR ACTUATOR - INSPECTION/CHECK
__________________________________________________
 1.  General
 A.  This procedure only has illustrations and data for the wear limits of the components on the push-pull cam fittings. For the removal and installation of a damaged component (AMM 52-31-02/401).
 TASK 52-31-02-706-001
 2.  Nose Cargo Door Linear Actuator Examination
___________________________________________
 A.  Access
 (1)  
Access Panel
 801 Door - Nose Cargo

 B.  
Linear Actuator Wear Limits

 S 216-005
 (1)  
Examine the bushings for worn areas (Figure 601).

 S 216-004

 (2)  
Examine the aft end fitting for worn parts (Figure 601).

 NOTE: This examination is only necessary when you replace the
____
 bushings.

 C.  Linear Actuator Shear Lockbolt
 S 716-006
 (1)  
When one or two both of the linear actuator shear lockbolt's is defective, continued operation is permitted. Make sure the nose cargo door is fully latched and is not used.

 S 966-007

 (2)  
The alternative BACB30FM8A7 shear lockbolt and BACC30M8 collar replace the shear lockbolt and the collar . This will let the continued operation with the nose cargo door operative if the shear lockbolt key is installed (AMM 52-31-02/801).

 S 966-008

 (3)  
Replace the linear actuator at a subsequent time when the spare linear actuator is available.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-31-02
 ALL  ú ú 02 Page 601 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 426-009
 (4) Install the linear actuator (AMM 52-31-02/401).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-31-02
 ALL  ú ú 02 Page 602 ú Oct 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 2(38)