52-32-12
 ALL  ú ú 02 Page 401 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

CARGO SIDE DOOR 
A 
BOLT ATTACHMENT SOLENOID (2 LOCATIONS) 
A  TUBE HOOK TORQUE SOLENOID RESTRAINT (2 LOCATIONS)  SOLENOID PLUNGER RELEASE MANUAL RESTRAINT ARM 
TORQUE HOOK TUBE 
DOOR 

Door Restraint Solenoid
Figure 401

ELECTRICAL
CONNECTOR

RESTRAINT SOLENOID
EYEBOLT
EYEBOLT TO RESTRAINT ARM CONNECTION
RESTRAINT ARM BOLT
RESTRAINT
ARM
0.03
INCH
0.01 CLEARANCE
A-A
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-32-12
 ALL  ú ú 02 Page 402 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 034-007
 (6)  Remove the eyebolt from the solenoid.
 TASK 52-32-12-404-008
 3.  Install the Door Restraint Solenoid___________________________________
 A. Consumable Materials
 (1)  
D00013 Grease - MIL-G-23827

 B.
References

 (1)  
IPC 52-32-12 Fig. 1

 (2)  
SSM 52-32-01

 (3)  
WDM 52-32-21

 C.
Access

 (1)  
Location Zone
 261 Main Deck STA 1720 To STA 2040, LH

 (2)  
Access Panels
 836L Door - Main Deck Cargo

 D.
Install the door restraint solenoid (Fig. 401)

 S 644-009
 (1)  
Apply grease on the eyebolt threads.

 S 434-020

 (2)  
Install the eyebolt in the solenoid plunger.

 S 824-010

 (3)  
Adjust the restraint arm as follows:

 (a)  
Make sure the clearance between the restraint arm and the torque tube is as shown (View A-A).

 (b)  
Adjust the adjustment bolt on the restraint arm if it is necessary.

 S 824-011
 (4)  
Adjust the solenoid as follows:

 (a)  
Hold the solenoid tightly in the installed position, do not install the attachment bolts, and temporarily connect the restraint arm to the eyebolt.

 (b)  
With the solenoid held tightly in the installed position, push up on the eyebolt until the solenoid plunger gets to the bottom of the solenoid (fully retracted).

 (c)  
Make sure the clearance between restraint arm and torque tube (section A-A) is 0.90-1.00 inch.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-32-12
 ALL  ú ú 02 Page 403 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (d)  If clearance is not correct, remove the solenoid and turn the eyebolt in or out of the solenoid to get the correct clearance.
 (5)  S 424-012Install the attachment bolts on the solenoid.
 (6)  S 434-013Connect the eyebolt to the restraint arm with the nut and washer.
 (7)  S 434-014Connect electrical connector DX214 or DX215 to the solenoid.
 (8)  S 864-015Remove the DO-NOT-CLOSE tags and close these circuit breakers for the side cargo door: (a) P415 Power Distribution Center - Right 1) 415F17 SIDE CARGO DOOR CONT (b) P715 Aux/Rxt No. 2 Power Center 1) SIDE CARGO DOOR PWR
 (9)  S 864-016Open the master latch lock handle.
 S 864-017

 (10)
 Put the door control switch in the OPEN position.

 S 734-018

 (11)
 Make sure the restraint arms retract clear of the stops on the hook torque tubes.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 2(166)