曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

____ switch. If you will adjust the initial (old) switch go directly to the switch operational check.
 1)  With the door closed, loosen the locknuts and adjust the switch in the bracket to get the initial adjustment (View C-C).
 CAUTION:_______IN CASE THE DOOR DOES NOT OPEN, STOP IMMEDIATELY. DO NOT OPERATE THE DOOR CONTROL SWITCH. HOLDING THE DOOR CONTROL SWITCH MAY DAMAGE THE ACTUATOR. WAIT AT LEAST 1 MINUTE BEFORE SECOND ATTEMPT. IF THE DOOR STILL DOES NOT OPEN, WAIT AT LEAST 10 MINUTES BEFORE THIRD ATTEMPT.
 2)  Open the cargo door approximately 1 - 2 feet.
 3)  Set the latch actuator (1) until it is against the external stops as follows (Fig. 402): a) Use a torque wrench with a dial indicator to manually
 turn the actuator counterclockwise at 25 |5 pound-inches torque. b) Monitor the point at which the torque increases by 15-20 pound-inches. c) Turn the manual drive 1/2 turn clockwise.
 NOTE: This is when the external stops are against
____ the latch actuator.
 d) Make sure the plunger for the latches open switch is not fully pushed in. 4) Turn the latch actuator (1) 15 turns clockwise.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-32-09
 ALL  ú ú 03 Page 413 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

747-400
MAINTENANCE MANUAL

TORQUE TUBE MIDSPAN LATCH 
A  A 
A  OPEN SWITCH MIDSPAN LATCH 
A 
OPEN SWITCH MIDSPAN LATCH  SWITCH OPEN LATCHES  SWITCH CLOSED LATCHES 
B
C  B  LOCK SECTOR LATCH 
C  CAM SHAFT LOWER LATCH 

Latch System Switch Adjustment
Figure 403 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-32-09
 ALL  ú ú 02 Page 414 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

MIDSPAN LATCH TORQUE TUBE
LATCHES
CLOSED
SWITCH

1.55
INCHES 1
1.49
THE EXTENDED POSITION OF THE SWITCH PLUNGER. THE PLUNGER DOES NOT TOUCH THE ACTUATOR HERE.
SWITCH
ACTUATOR
LOWER LATCH
SWITCH
CAM SHAFT
LATCHES OPEN
BRACKET SWITCH
B-B
1 1.17 INCHES
THE EXTENDED POSITION OF THE SWITCH PLUNGER. THE PLUNGER DOES NOT TOUCH THE ACTUATOR HERE.
SWITCH ACTUATOR
1 INITIAL SWITCH ADJUSTMENT ONLY. SEE TEXT FOR FINAL ADJUSTMENT THE EXTENDED POSITION
SWITCH OF THE SWITCH PLUNGER.
ACTUATOR THE PLUNGER DOES NOT
TOUCH THE ACTUATOR HERE.
1.54
INCHES 1
1.52
SWITCH
BRACKET
MIDSPAN LATCH OPEN SWITCH
A-A
LOCKNUTS LATCH TORQUE TUBE
SWITCH BRACKET
C-C
Latch System Switch Adjustment
Figure 403 (Sheet 2)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-32-09
 ALL  ú ú 02 Page 415 ú Feb 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
 (b)

A
747-400 MAINTENANCE MANUAL
 5) Make sure the striker plate is not against the switch plunger. 6) Disconnect electrical connector DX225C from the cargo door junction box. 7) Adjust the switch to make sure there is continuity between pins 21 and 22 of connector DX225C as the latch actuator
 (1) is turned 8 |1/4 turns counterclockwise. (The switch operates 7 |1/4 turns before the external stops contacted [open] position [Fig. 402].)
 NOTE: The switch must operate while the latch actuator is
____ turned to the open stops (counterclockwise). One turn of the limit switch locknut will change the switch operation point approximately one turn on the latch actuator.
 8) Connect electrical connector DX225C to the cargo door junction box. 9) Turn the latch actuator (1) counterclockwise to the fully
 open position before you operate the door.Do the operational check of the latches open switch as follows: 1) Close the door to its fully closed position.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 2(159)