S 865-153
CAUTION: MAKE SURE THAT THE PITOT LINE PRESSURE IS EQUIVALENT OR MORE
_______ THAN THE STATIC LINE PRESSURE. KEEP THE STATIC PRESSURE CHANGES LESS THAN 5000 FEET FOR EACH MINUTE. MAKE SURE THAT THE DIFFERENTIAL PRESSURE STAYS BETWEEN 0 AND 10.19 INCHES OF MERCURY. YOU CAN CAUSE DAMAGE TO THE PITOT-STATIC SYSTEM.
(4) Open the static cutoff valve.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-11-00
ALL ú ú 03 Page 579 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 865-310
(5) Put the alternate static system to ambient pressure.
S 085-154
CAUTION: DO NOT DISCONNECT THE PNEUMATIC TEST SET WHEN THE PITOT-STATIC
_______ SYSTEM IS NOT AT AMBIENT PRESSURE. YOU CAN CAUSE DAMAGE TO THE EQUIPMENT.
(6) Disconnect the pneumatic test set from the test fitting.
S 085-515
WARNING: FAILURE TO REMOVE THE VINYL ADHESIVE TAPE FROM THE STATIC PORTS
_______ BEFORE FLIGHT MAY CAUSE LARGE ERRORS IN AIRSPEED SENSING AND ALTITUDE SENSING SIGNALS, WHICH MAY LEAD TO LOSS OF SAFE FLIGHT.
CAUTION: MAKE SURE THAT YOU REMOVE ALL OF THE PIECES OF TAPE FROM EACH
_______ PITOT-STATIC PROBE. THE SYSTEM WILL NOT OPERATE CORRECTLY WHEN THE TAPE IS IN ITS POSITION.
(7)
Remove the vinyl adhesive tape from the left and right alternate static pressure ports.
S 215-156
(8)
Examine the pitot-static probe static ports for unwanted materials and rough locations on the inner and outer surfaces (Ref 34-11-01/601).
S 865-311
(9)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a) P6 Main Power Distribution Panel
1) 6E01 PRIM T/E FLAP CONT AC
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-11-00
ALL ú ú 01 Page 580 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
2) 6E02 PRIM T/E FLAP CONT DC
3) 6D30 PROBE HEAT PITOT L
4) 6D31 PROBE HEAT PITOT R
5) 6D32 PROBE HEAT AUX PITOT L
6) 6D33 PROBE HEAT AUX PITOT R
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-11-00
ALL ú ú 01 Page 580A ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
PITOT-STATIC PROBE - REMOVAL/INSTALLATION
_________________________________________
1. General_______
A. This subject contains two tasks. The first task is to remove a pitot-static probe. The second task is to install a pitot-static probe. The second task includes a test of the pitot-static probe installation.
B. Four pitot-static probes are installed on the external surface of the airplane. Two probes are installed forward of the No. 1 left door at STA 270, WL 200. Two probes are installed forward of the No. 1 right door at STA 270, WL 200.
TASK 34-11-01-024-016
2. Pitot-Static Probe Removal (Fig. 401)__________________________
A. Standard Tools and Equipment
(1) Sealant Removal Tool - hardwood or plastic
B. References
(1) AMM 51-31-01/201, Seals and Sealing
C. Access
(1) Location Zones
113 Nose Gear Well, LH
211 Passenger Cabin Nose to First Door, LH
114 Nose Gear Well, RH
212 Passenger Cabin Nose to First Door, RH
D. Remove the Pitot-Static Probe
S 864-017
(1) Open these circuit breakers and attach the DO-NOT CLOSE tags:
(a) P6 Main Power Distribution Panel
1) 6D30, PROBE HEAT PITOT L
2) 6D31, PROBE HEAT PITOT R
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 導航 NAVIGATION 1(71)
