(c)  
Remove the clamps that you put on the cables in the removal procedure.

 (d)  
Adjust the turnbuckles equally to put a tension of 250 -20 pounds on cables RA and RB (Fig. 402).

 (e)  
Remove rig pins R-1, R-2, R-3, and R-4.

 (f)  
Move the rudder pedals through 25 cycles.

 (g)  
Install rig pins R-3 and R-4.

 (h)  
Equally adjust the two turnbuckles to get the tension shown in Fig. 402 in cables RA and RB.

 (i)  
Make sure rig pins R-3 and R-4 can be easily removed and installed.

 (j)  
Remove rig pins R-3 and R-4.

 (k)  
Move the rudder pedals through one cycle.

 (l)  
Make sure the tension in the cables, RA and RB, is correct.

 (m)  
Install the locking clips on the turnbuckles.

 (n)  
Apply a thin layer of corrosion preventive compound to the threads that you can see.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-06
 ALL  ú ú 01 Page 410 ú Oct 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 714-033
 (18)
 Move the rudder pedals through one cycle.

 (a)  
Make sure the rudder pedals move smoothly.

 (b)  
Make sure the rudder aft quadrant moves through its full travel.

 NOTE: The aft rudder quadrant moves through its full travel if
____ it touches the stop at each end of its travel.
 S 824-035
 (19)
 Adjust and do a check of the position transducer for the rudder pedals (Ref 27-08-02/401).

 G.
Put the Airplane Back to Its Usual Condition.

 S 414-036
 (1)  
Install the ceiling panels.

 S 864-038

 (2)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P180, DC Power Distribution Panel,
 1) 180H8 ELEV/RUD VLV SYS 1
 2) 180E7 ELEV/RUD VLV SYS 2
 3) 180H23 ELEV/RUD VLV SYS 3
 4) 180E22 ELEV/RUD VLV SYS 4

 S 864-039
 (3)  
Find the switches for the FLT COLTROL HYD POWER on the Pilot's Overhead Maintenance Panel, P461.

 (a)  
Put the TAIL switches in the NORM position.

 S 084-064
 WARNING:_______MAKE SURE THE NOSE LANDING GEAR IS POINTED FORWARD. IF THE TIRES ARE NOT PARALLEL WITH THE AIRPLANE, THEY CAN TURN QUICKLY WHEN YOU REMOVE THE RIG PIN. THIS CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (4)  
Remove the rig pin from the steering metering valve for the nose landing gear (Ref 32-50-00/201).

 (5)
Remove electrical power if it is not necessary (Ref 24-22-00/201).

 S 864-042
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-06
 ALL  ú ú 03 Page 411 ú Oct 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 RUDDER FORWARD QUADRANT - INSPECTION/CHECK
__________________________________________
 1.  General_______
 A.  This procedure has one task. The task is an inspection of the rudder forward quadrant.
 B.  In this procedure you measure the inner or outer diameter of the parts which attach the rudder forward quadrant to the captain's rudder pedal yoke. The parts include bearings and bolts.
 C.  You must disassemble the rudder formard quadrant to do this procedure.
 TASK 27-21-06-206-001
 2.  Rudder Forward Quadrant Inspection__________________________________
 A.  Standard Tools and Equipment
 (1)  
Micrometer - 0-1 inch and 1-2 inch

 (2)  
Vernier Caliper

 B.  
References

 (1)  
27-21-06/401, Rudder Forward Quadrant

 C.  
Access

 (1)  
Location Zone
 221 Control Cabin, LH
 222 Control Cabin, RH
 211 Passenger Cabin-Nose to First Door, LH
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(92)