(2)  
MIT65B04000 Kit (Rigging Pins) (Optional) ~................................................................... | Pin | Designation | Length (inch) | Dia (inch) | Qty | ..................................................................... | -20 | A/S-1 | 2.0 | 0.309-0.311| 2 | 2.........….................….................…..............…......1

 B.  
References

 (1)  
AMM 24-22-00/201, Manual Control

 (2)  
AMM 27-51-00/201, Trailing Edge Flap System

 (3)  
AIPC 27-18-01, Fig. 1

 (4)  
SSM 27-18-01

 (5)  
WDM 27-18-11

 C.  
Access

 (1)  
Location Zones 591 Rear Spar to Trailing Edge, LH at Outboard Aileron 573 Rear Spar to Trailing Edge, LH at Inboard Aileron 673 Rear Spar to Trailing Edge, RH at Inboard Aileron 691 Rear Spar to Trailing Edge, RH at Outboard Aileron

 (2)  
Access Panel 591CB Outboard Aileron Access Panel (LO Transmitter) 573CB Hydraulic Access Panel (LI Transmitter) 673CB Hydraulic Access Panel (RI Transmitter) 691CB Outboard Aileron Access Panel (RO Transmitter)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-18-01
 ALL  ú ú 03 Page 404 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 D. Install the Aileron Position Transmitter
 S 434-011
 (1)  
Assemble the transmitter assembly:

 (a)  
Put the transmitter into the bracket until the inner clamping screw can engage the circumferential groove on the transmitter. 1) Install the transmitter clamping screws.

 a) Do not tighten the screw.

 (b)  
Turn the transmitter until E|Z (electrical zero) index mark on the transmitter housing align with the centerline of the rig pin holes.

 (c)  
Lightly tighten the transmitter clamping screws.

 (d)  
Put the transmitter shaft into the crank until the shaft clamping screw can engage circumferential groove on the shaft.

 (e)  
Install the shaft clamping screw, washer, and nut. 1) Do not tighten the nut.

 (f)  
Align the index mark on the shaft with the centerline of the rig pin slot in the crank.

 (g)  
Tighten the shaft clamping screw to 5-10 pound-inches.

 S 424-012
 (2)  
Install the transmitter assembly:

 (a)  
Set the transmitter, the bracket, and the crank assembly on the airplane. 1) Install two screws, washers, and nuts that attach the

 bracket to the airplane structure. a) Tighten the nuts to 20-30 pound-inches.

 (b)  
Install the screw, washer, and nut that attach the control rod to the crank. 1) Tighten the nut to 5-10 pound-inches.

 S 434-012
 (3)  
Install the bonding jumper.

 S 434-013

 (4)  
Install the electrical connector.

 E.
Adjust the Aileron Position Transmitter

 (1)  
Do this task: "Supply Electrical Power" (AMM 24-22-00/201).

 S 864-016

 (2)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P6, Main Power Distribution Panel
 1) 6J21, SPLR/ALRN IND
 2) 6J20, SPLR/ALRN SENSOR

 (3)  
Make sure that the ailerons are in the neutral position.

 S 864-014
 S 864-018
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-18-01
 ALL  ú ú 01 Page 405 ú Feb 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 494-018
 (4)  Install the rig pin through the crank and the outer hole of the bracket.
 NOTE: You may have to adjust the control rod to install the rig
____
 pin.

 S 824-019
 (5)  
Adjust the aileron position transmitter:

 (a)  
Loosen the transmitter clamping screws.

 (b)  
For the outboard aileron, adjust the transmitter body.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(36)