(3)  
24-22-00/201, Manual Control

 (4)  
27-21-15/401, Upper Rudder Actuators

 (5)  
29-11-00/201, Main Hydraulic Supply System

 (6)  
32-50-00/201, Steering

 (7)  
IPC 27-21-01, Fig. 2

 (8)  
IPC 55-40-52, Fig. 1

 E.
Access

 (1)  
Location Zone 324 Vertical Fin, Rear Spar to Trailing Edge 325 Rudder, Lower 326 Rudder, Upper

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-03
 ALL  ú ú 03 Page 415 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

 (2)  
Access Panel
 324CL Inspection Access Panel
 324DL Inspection Access Panel
 324EL Inspection Access Panel
 324GL Inspection Access Panel
 324HL Inspection Access Panel
 324UL Inspection Access Panel

 F.
Prepare to Install the Hinge

 S 224-118
 (1)  
Make sure the rudder hinge segments and the bolt for the hinge are not worn too much.

 G.
Install the Hinge

 S 424-090
 WARNING: MAKE SURE PERSONS AND EQUIPMENT ARE CLEAR BELOW THE RUDDERS.
_______ OBJECTS CAN FALL AND CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1)  
Do these steps to install hinge No. 2 or 3.

 (a)  
Apply corrosion preventive compound to the vertical fin, where the bearing assembly (1) will touch it.

 (b)  
Put the bearing assembly (1) in its position on the vertical fin.

 (c)  
Install the bolts (2), the washers (3), and the nuts (4) (8 locations). Tighten the nuts (4) to 80-100 pound-inches.

 (d)  
Connect the bonding jumper (20) to the rudder.

 (e)  
Apply a thin layer of grease to the pin (11 or 21).

 (f)  
Install the pin (11) in hinge No. 2, or the bushing (22) and the pin (21) in hinge No. 3.

 (g)  
Tighten the threaded bushing(s) (12) with your hand until there is no clearance between the bushing and the bearing.

 (h)  
Install lockwire on the bushing(s) (12) in a direction that will keep them tight.

 (i)  
Install the washer (18), and the nut (17). Also, install the washers (19) until the lockbolt (14) engages the nut (17) correctly. 1) Tighten the nut (17) to 2000-2400 pound-inches. 2) If it is necessary, tighten the nut (17) to a maximum of

 3200 pound-inches to let you install the lockbolt (14).

 (j)  
Install the lockbolt (14), the washer (15), and the nut (16).

 (k)  
Install Lockwire on the pin (11 or 21).

 (l)  
Put sealant into the lockwire holes that are in the actuator clevises. Fully fill the holes, and put a bead of sealant around the holes.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-03
 ALL  ú ú 03 Page 416 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 S 424-091
 WARNING: MAKE SURE PERSONS AND EQUIPMENT ARE CLEAR BELOW THE RUDDERS.
_______ OBJECTS CAN FALL AND CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (2)  
Do these steps to install hinge No. 6.

 (a)  
Put the hinge lower assembly (5) in its position on the rudder front spar.

 NOTE: The hinge upper assembly (10) must be attached to the
____
 hinge lower assembly (5).

 (b)  
Install the bolts (6) and the washers (7) (2 locations). Tighten the bolts (6) to 65-100 pound-inches.

 (c)  
Install the bolts (9) and the washers (8) (4 locations). Tighten the bolts (9) to 65-100 pound-inches.

 (d)  
Put the hinge upper segment (49) and the hinge lower
 segment (45) in their position on the vertical fin.

 (e)  
Install the bolts (48), the washers (47) (at each end of the bolts), and the nuts (46) (4 locations). Tighten the bolts (48) to 300-350 pound-inches.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機(jī)維護(hù)手冊(cè) 飛行操縱 FLIGHT CONTROLS 2(84)