RUDDER RB CABLE
FORWARD
QUADRANT
A
RIG PIN R-3 RIGGING
SEE A
PIN R-1
CABIN FLOOR
INTERCOSTAL
RA CABLE
BUS ROD
PUSHROD FOR THE
A
NOSE WHEEL STEERING
LEFT SIDE
SEE B FLEX SHAFT
SUPPORT STRUCTURE
WASHER SHAFT RETAINING NUT
FWD JACKSHAFT FOR THE RUDDER FORWARD QUADRANT
A
Rudder Forward Quadrant Installation
Figure 401 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-06
ALL ú ú 01 Page 402 ú Jun 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
SCREW
(3 LOCATIONS) RETAINER
Rudder Forward Quadrant Installation
Figure 401 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-06
ALL ú ú 01 Page 403 ú Jun 10/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
S 014-006
(4)
Open the two forward center ceiling panels in the main deck compartment (in front of the No. 1 door) to get access to the rudder forward quadrants.
S 014-007
(5)
Open the second inboard ceiling panel (panel No. 241CL) aft of the No. 2 door in the main deck compartment for access to the turnbuckles.
D.
Procedure
S 844-043
(1)
Do these steps before you remove the right rudder forward quadrant:
(a)
Install a clamp on cables RA and RB (to keep the cables tight) aft of the turnbuckles at ceiling panel No. 241CL.
(b)
Loosen the turnbuckles to loosen cables RA and RB. Loosen the cables together to keep the tension the same in each cable.
(c)
Disconnect cables RA and RB from the rudder forward quadrant.
(d)
Put tags on the cables for identification.
S 024-012
(2)
Do these steps to remove the rudder forward quadrant:
(a)
Disconnect the bus rod from the rudder forward quadrant.
(b)
Disconnect the pushrods, for the rudder pedals, from the rudder forward quadrant.
(c)
For the left rudder forward quadrant, disconnect the pushrod for the nose wheel steering.
(d)
For the right rudder forward quadrant, disconnect the pushrod to the position transducer.
(e)
Remove the clamps from the flexshaft.
(f)
Disconnect the shaft retaining nut from the flexshaft.
(g)
Hold the shaft retaining nut and the washer and pull the flexshaft clear of the support structure.
(h)
Remove the two bolts that attach the ceiling support clip to the support beam for the lower bearing.
(i)
Remove the ceiling support clip from the support tee.
NOTE: If the ceiling support clip is attached with rivets,
____
drill the rivets.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-21-06
ALL ú ú 01 Page 404 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
(j)
Remove the two bolts at each end of the support beam for the lower bearing.
(k)
Remove the drip shield panel (inboard of the quadrant assembly) to get access to the bolts for the upper bearing housing.
(l)
Remove the four bolts that attach the upper bearing housing to the airplane.
(m) 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(89)
