27-21-03
 ALL  ú ú 03 Page 413 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  P180, DC Power Distribution Panel
 1) 180E7 ELEV/RUD VLV SYS 2
 2) 180E22 ELEV/RUD VLV SYS 4
 3) 180H8 ELEV/RUD VLV SYS 1
 4) 180H23 ELEV/RUD VLV SYS 3

 S 014-117
 (4)  
Remove the applicable access panels (Ref 06-09-07/201).

 E.
Remove the Hinge

 S 024-086
 WARNING: MAKE SURE PERSONS AND EQUIPMENT ARE CLEAR BELOW THE RUDDERS.
_______ OBJECTS CAN FALL AND CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1)  
Do these steps to remove hinge No. 2, or 3.

 (a)  
Remove the lockbolt (14), the washer (15), and the nut (16).

 (b)  
Remove the nut (17).

 (c)  
Loosen the threaded bushings (12) until their ends are fully retracted.

 (d)  
Remove the pin (11 or 21) from the hinge.

 (e)  
Remove the bolts (2) (8 locations).

 (f)  
Remove the bonding jumper (20) from the rudder.

 (g)  
Remove the bearing assembly (1).

 S 024-087
 WARNING: MAKE SURE PERSONS AND EQUIPMENT ARE CLEAR BELOW THE RUDDERS.
_______ OBJECTS CAN FALL AND CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (2)  
Do these steps to remove hinge No. 6.

 (a)  
Remove the nut (28) and the bolt (23).

 (b)  
Remove the bolts (48) (4 locations).

 (c)  
Remove the bonding jumper (20) from the rudder.

 (d)  
Remove the hinge upper segment (49) and the hinge lower segment (45).

 (e)  
Remove the bolt (9) (4 locations).

 (f)  
Remove the bolt (6) (2 locations).

 (g)  
Remove the hinge lower assembly (5) (with the hinge upper assembly (10) attached) from the rudder front spar.

 S 024-088
 WARNING: MAKE SURE PERSONS AND EQUIPMENT ARE CLEAR BELOW THE RUDDERS.
_______ OBJECTS CAN FALL AND CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (3)  
Do these steps to remove hinge No. 7 or 8

 (a)  
Remove the nut (40).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-03
 ALL  ú ú 03 Page 414 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (b)  
Remove the lockbolt (14), the washer (15), and the nut (16).

 (c)  
Remove the nut (17).

 (d)  
Loosen the threaded bushings (12) until their ends are fully retracted.

 (e)  
Remove the pins (34, 35), or (43, 44) from the hinge.

 (f)  
Remove the bolt (2) (8 locations).

 (g)  
Remove the bonding jumper (20) from the rudder.

 (h)  
If access to the bearing assembly (1) is difficult, do the steps that follow: 1) Disconnect the 3 actuators of the power control package of

 the upper rudder from the upper rudder. 2) Move the upper rudder full right.

 (i)  
Remove the bearing assembly (1).

 TASK 27-21-03-404-089
 5.  Rudder Hinge No. 2, 3, 6, 7 or 8 Installation (Fig. 402)_____________________________________________
 A. General
 (1)  
Hinges No. 2 and 7 have two adjustable bushings. Hinges No. 3 and 8 have one adjustable bushing.

 (2)  
Hinges No. 7 and 8 have two pins that are concentric. Hinges No. 2 and 3 have only one pin.

 B.
Special Tools and Equipment

 (1)  
ST2580-267 Spanner Wrench Adapter Set

 (2)  
2MIT65B04011-41 Nose Gear Rig and Tow Safty Pin

 (3)  
Milliohmmeter - 0 to 0.1 ohm range.

 C.
Consumable Materials

 (1)  
A00247 Sealant - BMS 5-95

 (2)  
C00174 Compound, Corrosion Preventive - MIL-C-16173

 (3)  
D00633 Grease - BMS 3-33 (Preffered).

 (4)  
D00013 Grease - MIL-G-23827 (Optional).

 D.
References

 (1)  
06-09-07/201, Fin and Rudder Access Doors and Panels

 (2)  
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 2(83)