曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 14. APU Lubrication (Fig. 2)
_______________
 A.  The APU lubrication system pressurizes the oil for the APU engine. The APU lubrication system supplies the oil to the gears and the bearings in the APU engine. The APU lubrication system has the oil pump, oil tank, oil cooler, and oil lines. For a more detailed description of the APU lubrication system, refer to AMM 49-91-00/001.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-00-00
 ALL  ú ú 08 Page 11 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / GTCP85-129 SERIES /737-300/400/500/ ENGINES/MAINTENANCE MANUAL ////////////////////////
15. APU Oil Indicating (Fig. 1)
__________________
 A.  The APU oil indicating system monitors the temperature, pressure, and quantity of the APU oil. The indicating lights for the APU oil indicating system are on the P5 forward overhead panel.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-00-00
 ALL  ú ú 04 Page 12 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
AIRBORNE AUXILIARY POWER - TROUBLESHOOTING
__________________________________________
 1.  General_______
 A.  This section gives a list and description of the controls and indicators for the APU. Also, this section gives the troubleshooting tips and the procedures to correct problems of the APU.
 B.  The troubleshooting tips give the cautions and the warnings that must be obeyed during troubleshooting.
 C.  The fault index gives the APU operation problems and the corrective action for each problem (Fig. 101).
 (1)  
The fault index has five groups of APU problems:

 (a)  
APU indication problems before the APU start

 (b)  
APU start problems

 (c)  
APU indication problems during the APU operation

 (d)  
APU indication problems during the APU shutdown

 (e)  
Additional APU problems for airplanes with the ETC.

 

 (2)  
The fault index will refer you to a figure to correct the problem.

 (a)  Each figure has a troubleshooting procedure. The troubleshooting procedure has two sections: 1) Possible Causes
 a)  The list of possible causes can be used if there is not much time. The possible causes are given in a sequence with the most possible and easiest cause at the top. The least possible and most difficult causes are at the bottom. The list of possible causes does not include defective wiring.
 2)  Fault Isolation a) The fault isolation is a diagram which gives the procedure to find the problem.
 2.  APU Control and Indicators__________________________
 A.  BAT Switch
 (1) The BAT switch supplies the power to the APU control system.
 B.  APU Master Switch
 (1)  When the APU master switch is moved to the START position, the start relay R5 is energized and the APU start sequence begins. In the ON position, the APU master switch supplies the power to the APU fuel valve and the air inlet door.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
 49-00-00
 ALL  ú ú 01 Page 101 ú Jul 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / GTCP85-129 SERIES /737-300/400/500/ ENGINES/MAINTENANCE MANUAL ////////////////////////
(2)  
In the ON position, the APU master switch supplies the power to the APU fuel valve and the air inlet door.

 (3)  
When the APU master switch is moved to the OFF position, power is supplied to the overspeed oscillator in the electronic speed switch to give a signal like an APU engine overspeed.

 C. DC AMPS Meter
 (1)  This meter will move in the negative direction when the APU starter engages. The DC AMPS meter will be a little negative during the starter operation.
 D. DC VOLTS Meter
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 AIRBORNE AUXILIARY POWER 1(9)