(2)
Open the access door to the actuator for the air inlet door.
S 225-004
(3)
Make sure the air inlet door aligns correctly for the open position:
S 015-003
(a) Measure the position of the air inlet door in the fully open position (Sheet 3).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
49-15-00
ALL ú ú 01 Page 501 ú Mar 15/92
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / GTCP85-129 SERIES /737-300/400/500/ ENGINES /MAINTENANCE MANUAL ////////////////////////
SEE A
AIR DIFFUSER
DUCT
SEE B
VORTEX
GENERATOR
AIR INLET DOOR
A FWD
PRESSURE
BULKHEAD AIR
INLET
DOOR
SEE E
AIR DIFFUSER
DUCT
FWD
ACTUATOR B
SEE C
Air Inlet Door Adjustment
Figure 501 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
49-15-00
ALL ú ú 01 Page 502 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
NUT
Air Inlet Door Adjustment
Figure 501 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
49-15-00
ALL ú ú 01 Page 503 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / GTCP85-129 SERIES /737-300/400/500/ ENGINES /MAINTENANCE MANUAL ////////////////////////
VORTEX GENERATOR
Air Inlet Door Adjustment
Figure 501 (Sheet 3)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
49-15-00
ALL ú ú 01 Page 504 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(b) If it is necessary, adjust the pushrod ends: 1) Remove the nuts, washers and bolts that connect the pushrods to the actuator arms. 2) Loosen the locknut of one pushrod end bearing on each pushrod.
3) Turn the pushrod ends until the air inlet door aligns in the limits.
NOTE: The pushrod end will move 0.02 inch (0.5 mm)
____ with one half turn of the pushrod end.
4) Tighten the locknuts of the pushrod end bearings.
5) Put the pushrods on the actuator arms.
6) Install the nuts, washers and bolts that connect the
pushrods to the actuator arms.
S 865-005
(4) Set these switches on the P5 forward overhead panel:
(a)
Remove the DO-NOT-OPERATE tag from the BAT switch.
(b)
Set the BAT switch to the ON position.
(c)
Remove the DO-NOT-OPERATE tag from the APU master switch.
(d)
Set the APU master switch to the OFF position.
S 225-006
(5) Make sure the air inlet door aligns correctly for the closed position:
(a)
Measure the position of the air inlet door in the closed position (Sheet 3).
(b)
If it is necessary, adjust the pushrod ends. The clearance between the air inlet door and the inlet throat must be correct.
NOTE: Do not adjust the position of the air inlet door out of
____ the limits for the open position.
S 905-007
(6) Do this task: "Air Inlet Door Switch Adjustment".
TASK 49-15-00-905-008
3. Air Inlet Door Switch Adjustment (Fig. 502)
________________________________
A. Access
(1) Location Zones
101 Control Cabin (Left)
701 Tail Compartment
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú 中國航空網(wǎng) m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊 AIRBORNE AUXILIARY POWER 1(130)
