曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 NOTE: If the adapter cable assembly is used, the test cable
____ assembly must be connected to the adapter cable assembly.
 (g)  Connect the electrical cable or test cable assembly (46) to the electronic speed switch (44) and the electrical connectors (45).
 (h) When you use the tester for the first time, do a check of the EGT loop resistance as follows: 1) Remove the screws that attach the instrument panel to the temperature indication circuit. 2) Lift the panel to get access to the components of the temperature indication circuit. 3) Tag and disconnect the wires from the EGT indicator terminals on the rear of the indicator case. 4) Use the wheatstone bridge or the multimeter to find the total resistance of the circuit between (and external to) the indicator and the thermocouple probe. a) The resistance must be 8.000 |0.035 ohms.
 5)  If the resistance is not in the limits, adjust the variable resistor in the tester to get the correct resistance. 6) Remove the wheatstone bridge or the multimeter.
 CAUTION: MAKE SURE YOU CONNECT THE WHITE (CHROMEL) WIRE TO THE
_______ "CR" TERMINAL. MAKE SURE YOU CONNECT THE GREEN (ALUMEL) WIRE TO THE "AL" TERMINAL. THE INCORRECT OPERATION OF THE TESTER CAN OCCUR IF YOU DO NOT CORRECTLY CONNECT THE WIRES.
 7) Connect the wires to the temperature indicator terminals. 8) Attach the instrument panel to the tester with the screws.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 49-11-00
 ALL  ú ú 08 Page 538 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(i)  
Disconnect the electrical connector (37) from the tachometer generator (36).

 (j)  
Connect the electrical cable or test cable assembly (46) to the tachometer generator (36) and the electrical connector (37).

 (k)  
Connect the electrical cable or test cable assembly (46) to the tester receptacle (13).

 S 725-052
 (5)  Do the opening rate test for the bleed air valve (Fig. 505):
 (a)  
Start the APU (AMM 49-11-00/201).

 (b)  
Let the engine operation become stable with no load applied.

 1)  With no load applied to the APU, the engine speed must become stable at 102.5% rpm maximum as shown on the tester indicator (15).

 (c)  
Set the APU BLEED switch on the P5 forward overhead panel to the ON position.

 (d)  
Set the air conditioning R PACK and L PACK switches to the ON position.

 (e)  
Set the tester load switch (29) to the ON position.

 (f)  
Measure the time between the operation of the tester load switch (29) until the fuel pressure gage (2) shows the first maximum indication. 1) The first maximum indication usually occurs in 12-14

 seconds and shows that the valve is open.

 (g)  
Monitor the engine speed on the indicator (15).

 1)  The engine speed must not decrease more than 3% of the engine rpm.

 (h)  
Monitor the engine speed on the tester indicator (15) with a full load applied to the APU. 1) The engine speed must become stable between 99.3% to 104.3%

 rpm with the load applied.

 (i)  
Monitor the EGT indicator (7) with the load applied.

 NOTE: This temperature must be 1202°F (650°C) or less.
____
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 49-11-00
 ALL  ú ú 09 Page 539 ú Mar 12/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / GTCP85-129 SERIES /737-300/400/500/ ENGINES /MAINTENANCE MANUAL ////////////////////////
UPPER
SHROUD

BLEED AIR DUCT
SEE  A  SEE  B 
BLEED AIR DUCT  ELECTRICAL PLUG  A
BLEED AIR VALVE  SEE  C  INBD 
FWD 
B

A  B  NUT 
ADJUSTMENT 
SCREW FOR THE  ADJUSTMENT 
RATE CONTROL  SCREW FOR THE 
A  B  RATE CONTROL 
BLEED 
AIR 
VALVE 
FWD 
FWD 
C  2 
C  1 
Bleed Air Valve Adjustments 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 AIRBORNE AUXILIARY POWER 1(107)