(a)  
Use the C32018-1 to protect the seals from the threads of the outer cylinder.

 S 828-067
 (23)
 Make sure the torsion link lugs on the inner cylinder are opposite the drag brace lug on the outer cylinder.

 S 438-068

 (24)
 Move the lower bearing (6) up against the seal assembly and the bearing and centering cam together into the outer cylinder.

 NOTE: The lower centering cam must come out of the lower end of
____ the outer cylinder by 0.03 to 0.06 inch. Make sure you align the upper centering cam and the lower centering cam. The notched slot of the lower cam must be in-line with the lobe of the upper cam.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-21-11
 ALL  ú ú 04 Page 816 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 438-069
 (25)
 Move the scraper adapter (15) together with the scraper ring (7) against the lower bearing.

 S 398-030

 (26)
 Apply corrosion preventive compound to the threads on the gland nut and the outer cylinder.

 S 828-070

 (27)
 Move the gland nut (8) into a position to attach it to the outer cylinder.

 NOTE: If you have problems with the installation of the lower
____ bearing into the outer cylinder, do these steps. Align the inner cylinder. Put a wooden block of equal dimensions on the two sides of inner cylinder below the gland nut. Lift the inner cylinder until the gland nut touches the outer cylinder.
 S 428-081
 (28) Tighten the gland nut to 175 - 200 foot-pounds.
 NOTE:  If it is necessary, loosen the gland nut slightly to align the slot for the installation of the gland nut lock.
 S 438-033
 (29)
 Install the gland nut lock (18).

 (30)
 Move the wheels aft until the lock brace assembly locks.

 (31)
 Install the ground lock (Ref 32-00-01/201).

 S 828-072

 (32)
 Make sure the torsion link lugs on the inner cylinder are opposite the drag brace lug on the outer cylinder.

 S 988-034
 S 498-035
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-21-11
 ALL  ú ú 03 Page 817 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 828-037
 (33)
 Make sure the length of the fully extended gear is 25.5 inches as shown on nose gear servicing chart (Ref 12-15-41/301).

 S 118-038

 (34)
 Clean the area for the new fillet seal with a new or clean white cloth and toluene.

 S 398-039

 (35)
 Use a brush to apply a thin layer of primer to the area of the gland

 nut.
 NOTE:____ You must let the primer dry a minimum of 1/2 hour before you
 apply the sealant.

 S 398-040
 (36)
 Apply the sealant.

 (a)  
Apply a bead of sealant around the outer cylinder of the shock strut and the gland nut.

 NOTE: Use a sealant gun for this.
____
 (b)  Use a spatula or the end of the sealant gun to make the fillet smooth.
 NOTE: When you make the fillet smooth, decrease the number of
____ air bubbles in the fillet as much as possible.
 NOTE: If the sealant bonds to the tool, apply a solution
____ of 15 to 20% isopropyl alcohol in distilled water to the tool. Use a polyethylene squirt bottle to apply the solution. This will prevent the contamination of the solution.
 (c)  Make the fillet a minimum of 0.08 inch thick at the interface of the gland nut and the shock strut. The fillet must extend 1/8 to 1/4 inch out on the gland nut and up the shock strut.
 NOTE: Make the fillet smooth immediately after you apply
____ the sealant. Do this because the fillet makes a skin a short time after it touches the air.
 S 648-041
 (37)
 Lubricate the gland nut with grease (four locations).

 S 648-042

 (38)
 Lubricate the bushing (12A), bolt (10), and bolt threads with grease.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 2(28)