(g)  
Install the cotter pin.

 S 434-016
 (15)
 Connect the electrical wire harness (11) to the lower torsion link (10).

 (a)  
Loosen the wire harness and install on torsion links.

 (16)
 Install the nose wheels (AMM 32-45-21/401).

 S 824-014

 (17)
 Adjust the safety sensor on the nose landing gear (AMM 32-09-02/501).

 S 414-015
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-21-31
 ALL  ú ú 05 Page 408 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 094-013
 (18)
 Remove the jack from the axle of the nose landing gear.

 S 584-012

 (19)
 Lower the nose of the airplane and remove the jacks (AMM 07-11-11/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-21-31
 ALL  ú ú 01 Page 409 ú Nov 15/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 NOSE LANDING GEAR TORSION LINKS - INSPECTION/CHECK
__________________________________________________
 1.  General
_______
 A.  This procedure only has illustration and a wear limits table which shows the data for wear limits. There are no procedures for the access, the removal, or the installation of the parts. Refer to the Nose Landing Gear Torsion Links - Removal/Installation for procedures to do these tasks.
 TASK 32-21-31-206-001
 2.  Wear Limits for the Torsion Links of the Nose Landing Gear (Fig. 601)
__________________________________________________________
 A.  Wear Limits for the Torsion Links
 S 226-002
 (1)  Refer to Fig. 601 for the inspection points and the wear limits table.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-21-31
 ALL  ú ú 02 Page 601 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

737-300/400/500
MAINTENANCE MANUAL

1. BUSHING/PIN
 (2 LOCATIONS)  A 
6. 
A 
STEERING  FWD 
COLLAR LUG 
C 
B 
PIN 
B 
C 
UPPER 
TORSION 
LINK 
2. BUSHING PIN APEX 
(2 LOCATIONS)  BOLT  8. 
A-A  8. 
3. BUSHING/BOLT
 (5 LOCATIONS) 
LOWER TORSION 
LINK 
4. BUSHING PIN
 (2 LOCATIONS) 
7. 
B-B 
PIN 
SHOCK STRUT  5. BUSHING/PIN
INNER CYLINDER  (2 LOCATIONS) 
LUG 
C-C 

Nose Landing Gear Torsion Links Installation
Figure 601 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-21-31
 ALL  ú ú 01 Page 602 ú Nov 15/93
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
INDEX NO.  PART NAME  DIM.  DESIGN LIMITS  WEAR LIMITS  REPLACE WORN PART  WORN PART REPAIR  REPAIR INSTR 
DIAMETER  MITTED WEAR DIM. PER- CLEAR-ANCE MAX DIA 
MIN  MAX 
1  BUSHING  ID  1.2500  1.2510  1.260  0.010  X 
PIN  OD  1.2490  1.2498  1.245  X  1 
2  BUSHING  ID  1.2500  1.2510  1.260  0.010  X 
PIN  OD  1.2490  1.2498  1.245  X  1 
3  BUSHING  ID  0.6250  0.6259  0.634  0.010  X 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 2(37)