S 034-003
(2)
Disconnect the actuating rod assembly from the trunnion link.
S 034-004
(3)
Disconnect the bonding jumper assembly from the structure.
S 034-005
(4)
Hold the door and remove the hinge bolts.
TASK 32-13-21-404-006
3. Main Landing Gear Wing Door Installation (Fig. 401)
________________________________________
A. Standard Tools and Equipment
(1) Test Set - Hydraulic; 0 - 3000 psi, 20 GPM
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-13-21
ALL ú ú 01 Page 401 ú Nov 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
TRUNNION
LINK
SEE A
SPECIAL BOLT STIFFENER
SEE C
WING DOOR
SEE B
STABILIZING MEMBER
ACTUATING HINGE BOLT ROD ASSEMBLY (2 LOCATIONS)
INNER
OUTER WING
DOOR FWD
DOOR WASHER
(4 LOCATIONS)
COTTER PIN
(2 LOCATIONS)
DOOR BOLT (TYPICAL)
NUT (2 LOCATIONS) INBD FWD
A
HINGE
STABILIZER
MEMBEROUTER DOOR
DOOR STOPCENTER
DOOR 0.50 |0.10 INCH
0.10 +0.04/-0.00 INCH FILLER PANELFWD
B
BOLT STIFFENER NUT (6 LOCATIONS)
NOTE: GEAR UP AND LOCKED.
C
Main Gear Wing Door Installation
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-13-21
ALL ú ú 01 Page 402 ú Mar 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
B.
C.
D.
E.
A
737-300/400/500MAINTENANCE MANUAL
(2)
ST918D - Mandrel, Bearing Press FittingConsumable Materials
(1)
G00000 - Chemical and Solvent Resistant Primer - BMS 10-11, Type 1.References
(1)
AMM 32-13-21/501, Main Landing Gear Wing door
(2)
AMM B57-15-00/401, Landing Gear Support BeamAccess
(1)
Location Zones 310 Left Main Landing Gear 410 Right Main Landing Gear
Prepare to Install the Wing Door
S 424-007
(1)
Install the initial wing door.
(a)
Put the door in its position and install the hinge bolts, washers, and nuts.
(b)
AIRPLANES WITH SELF-LOCKING NUT; Tighten the self-locking nut to 180-250 pound-inches (20.3-28.2 newton-meters).
(c)
AIRPLANES WITH COTTER PIN;
Tighten the nut to 100-140 pound-inches (11.3-15.8
newton-meters).
1) If it is necessary, loosen the nut to the nearest
castellation to align the hole for the cotter pin.
(d)
Install the cotter pin.
(e)
Adjust the actuating rod assembly to a nominal of 7.60 inches after you install a new actuating rod .
NOTE: The distance of 7.60 inches is measured between the
____ centers of the bolts attach to the end.
(f)
Connect the actuating rod assembly.
(g)
Tighten the nut to 450-500 pound-inches (50.8-56.5
newton-meters).
1) If it is necessary, loosen the nut to the nearest
castellation to align the hole for the cotter pin.
(h)
Install the cotter pin.
(i)
Connect the bonding jumper.
(j)
Adjust the wing door on the main landing gear after you install a new actuating rod (AMM 32-13-21/501).
S 424-008
(2)
Install the replacement wing door.
(a)
Remove special bolts and install the replacement bolts with undrilled heads (part number 69-54970) in the stabilizer beam.
(b)
Make a mark on the bolts and the stabilizer beam to make sure you install the bolts correctly.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-13-21
ALL ú ú 03 Page 403 ú Nov 12/01
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 2(5)
