32-21-00
 ALL  ú ú 02 Page 408 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (4)  
AMM 32-09-02/501, Nose Landing Gear Safety Sensor

 (5)  
AMM 29-15-00/201, Hydraulic Systems A and B

 (6)  
AMM 32-09-02/401, Nose Landing Gear Safety Sensors

 (7)  
AMM 32-21-51/401, Nose Landing Gear Trunnion Bearing

 (8)  
AMM 32-22-11/401, Nose Landing Gear Wheel Well Doors

 (9)  
AMM 32-33-00/501, Nose Landing Gear Extension and Retraction

 (10)
 AMM 32-35-00/501, Nose Landing Gear Manual Extension System

 (11)
 AMM 32-51-00/501, Nose Wheel Steering System

 E.
Prepare for the Installation of the Nose Landing Gear

 S 224-034
 (1)  Examine the distance between the trunnion bearings of the nose landing gear in the wheel well structure (AMM 32-21-51/401).
 S 434-139
 WARNING: USE NITRILE GLOVES FOR SKIN PROTECTION AGAINST BMS 3-27
_______ (MASTINOX 6856K). IF MASTINOX GETS ON YOUR SKIN, IMMEDIATELY REMOVE IT WITH WATER. IF THIS MATERIAL GETS IN YOUR EYES, IMMEDIATELY FLUSH YOUR EYES WITH WATER AND GET MEDICAL AID. THIS MATERIAL CONTAINS VERY POISONOUS AND FLAMMABLE AGENTS WHICH CAN CAUSE INJURIES TO PERSONS.
 CAUTION: REMOVE UNWANTED MASTINOX FROM SURFACES WHICH WILL BE
_______ LUBRICATED. IF YOU APPLY MASTINOX TO JOINTS THAT TURN, FAILURE OF THE LANDING GEAR TO EXTEND OR RETRACT COULD OCCUR.
 (2)  
Make sure the trunnion pins (20) are not fully inserted in their trunnions (4 and 16), but must not come out more on the outboard edge of the trunnion on the gear.

 (3)  
Install the oleo lock assembly for the nose landing gear.

 S 934-080

 (4)  
Make a reference line mark through the center of each lockpin hole of the trunnion pin to the inboard end of each trunnion pin (20).

 S 984-081

 (5)  
Set the nose landing gear in the vertical position for installation to be lifted on jacks and to put in the trunnion pins.

 S 494-093
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 32-21-00
 ALL  ú ú 02 Page 409 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 F. Procedure to Install the Nose Landing Gear
 S 434-083
 (1)  Hold and lift the gear with an axle jack to install the trunnion pins (20) into their spherical bearings (13) on each side of the nose wheel well.
 NOTE: It is important for the trunnion axis of the gear to align
____ with the spherical bearings on each side of the nose wheel well while you lift the gear on axle jack.
 S 584-075
 (2)  
Lift the gear on jacks to the correct height.

 S 434-084

 (3)  
Lightly hit the trunnion pin (20) in place in each of the
 trunnion (16) and the spherical bearing (13).

 NOTE: It is important for the lockpin hole in the trunnion pin to
____ align with the mating hole in the trunnion when you install the trunnion pin.
 S 094-074
 (4)  
Remove the axle jack.

 S 114-095

 (5)  
Clean the trunnion pin lockpins (15) with solvent.

 S 624-140
 WARNING: USE NITRILE GLOVES FOR SKIN PROTECTION AGAINST BMS 3-27
_______ (MASTINOX 6856K). IF MASTINOX GETS ON YOUR SKIN, IMMEDIATELY REMOVE IT WITH WATER. IF THIS MATERIAL GETS IN YOUR EYES, IMMEDIATELY FLUSH YOUR EYES WITH WATER AND GET MEDICAL AID. THIS MATERIAL CONTAINS VERY POISONOUS AND FLAMMABLE AGENTS WHICH CAN CAUSE INJURIES TO PERSONS.
 CAUTION: REMOVE UNWANTED MASTINOX FROM SURFACES WHICH WILL BE
_______ LUBRICATED. IF YOU APPLY MASTINOX TO JOINTS THAT TURN, FAILURE OF THE LANDING GEAR TO EXTEND OR RETRACT COULD OCCUR.
 (6)  
Apply a corrosion preventive compound to each of the lockpin (15) (AMM 12-21-21/301).

 S 434-097

 (7)  
Install the lockpin (15) on the two sides of the left and the right trunnion pins.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 2(14)