WARNING: MAKE SURE THAT YOU INSTALL THE GROUND LOCK ASSEMBLIES IN
_______ THE MAIN LANDING GEAR TO PREVENT THE ACCIDENTAL OPERATION OF THE GEAR. IT CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT IF THE GEAR RETRACTS.
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-33-41
ALL ú ú 01 Page 402 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(k) (l) (m) Do a check on the cylinder hydraulic connections for leakage.Extend the gear and install the ground lock assembly (AMM 32-00-01).Lower the airplane.
NOTE:____ Remove the jacks.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-33-41
ALL ú ú 01 Page 403 ú Jul 15/96
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
NOSE GEAR LOCK MECHANISM - REMOVAL/INSTALLATION
_______________________________________________
TASK 32-33-51-004-001
1. Nose Gear Lock Mechanism Removal (Fig. 401)
________________________________
A. Equipment
(1)
Ground Lock Assemblies (AMM 32-00-01/201)
B.
Prepare for the procedure.
S 864-002
(1)
Make sure that you install the ground lock assemblies in the main gear (AMM 32-00-01/201).
S 864-012
(2)
Lift the airplane nose until the nose gear wheels are clear the ground (AMM 07-11-21/201).
S 864-013
(3)
Remove the ground lock assembly for the nose gear
(AMM 32-00-01/201).
C.
Procedure
S 024-003
(1)
Remove the bolt (14) to disconnect the lock link (6) from the drag brace upper and the lower links (8) and (13):
(a)
Remove the spacer bushing (11) and (12) from each lock link (6).
(b)
Remove the bolt from the bottom end of the lock actuator.
(c)
Remove the nuts and washers from each end of the lock brace shaft (19).
(d)
Extend the springs (1) and (5).
NOTE: Move the ends of the spring off the lock brace
____
shaft (19).
(e) Remove the bolt (17) and the shaft (19).
NOTE: You can put laminated shims between the lock brace (3)
____ and the fitting (20). Keep the shims for the re-installation.
(f) Remove the lock sensor from the support bracket.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-33-51
ALL ú ú 02 Page 401 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
SEE A
SEE D
SEE B
SEE C
20. FITTING
5. SPRING 19. SHAFT 17. BOLT ACTUATOR 16. LOCK
ATTACHMENT 18. UPPER BOLT
HOSES HYDRAULIC 1 3. LOCK BRACE 1. SPRING
LOCKBRACE A FWD
HOSE GUARD 1
FWD
D
1 NOT ON ALL AIRPLANES
Nose Gear Lock Mechanism Installation Figure 401 (Sheet 1)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
32-33-51
ALL ú ú 02 Page 402 ú Jul 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500
MAINTENANCE MANUAL
SPRING SHIM
RETAINER BOLT 7. NUT
SHIM
1. SPRING
7. NUT
6. LOCK LINK
21. LOCK SENSOR TARGET
2. INDICATORS
5. SPRING 3. LOCK BRACE
4. BOLT
FWD
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 起落架 LANDING GEAR 2(118)
