S 167-021
 (2)  Do these steps to clean the flame arrestor:
 (a)  
Prepare a weak solution of the water and the detergent in the bucket.

 (b)  
Put the flame arrestor fully into the solution for a minimum of five minutes.

 (c)  
Remove the flame arrestor from the solution.

 (d)  
With the air gun, blow away the particles which cause a blockage in the air holes in the flame arrestor.

 S 427-002
 CAUTION: DO NOT CAUSE DAMAGE TO THE FLAME ARRESTOR WHILE YOU REPLACE IT.
_______ THE FIT IS TIGHT AND THE FLAME ARRESTOR IS EASILY DAMAGED.
 (3)  
Replace the flame arrestor in the shroud drain line.

 S 437-001

 (4)  
Connect and tighten with your hand the coupler which contains the flame arrestor (AMM 28-22-15/401).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 28-13-21
 ALL  ú ú 01 Page 702 ú Mar 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 AIR VENT SCOOP FLAME ARRESTER - REMOVAL/INSTALLATION
____________________________________________________
 1.  General_______
 A.  This procedure has two tasks:
 (1)  
The removal of the flame arrester for the air vent scoop

 (2)  
The installation of the flame arrester for the air vent scoop.

 B.  The flame arrester unit is made of stainless steel, and it is made in a cellular-core pattern. It is installed on the top flange of the air stack on the access panel (No. 14) for the air vent scoop (Fig. 401). If the flame arrester cells are blocked with particles, you can usually clean the flame arrester while it is attached to the stack. To do this, you put the access panel assembly fully into a weak soap solution. Then you use an air gun to open the blocked cells.
 C.  If it is necessary to remove the flame arrester, you must seal the mounting flange again when you install the flame arrester.
 TASK 28-13-31-004-001
 2.  Flame Arrester Removal (Fig. 401)______________________
 A.  Equipment
 (1)  Tools - sealant removal, cutting, and fairing
 B.  References
 (1)  
AMM 24-22-00/201, Manual Control

 (2)  
AMM 28-11-11/401, Wing Fuel Tank Access Panels

 C.  Access
 (1)  
Location Zones
 304 Left Fuel Vent Surge Tank
 404 Right Fuel Vent Surge Tank

 (2)  
Access Panels
 7102 Surge Tank Vent Scoop Door
 7502 Surge Tank Vent Scoop Door

 D.  Procedure
 S 864-002
 (1)  
Make sure the airplane is correctly grounded to an approved and identified ground.

 S 864-003

 (2)  
Unless the applicable surge tank is prepared for entry, do these safety checks:

 (a)  
Remove the electrical power from the airplane (AMM 24-22-00/201). 1) Do not connect the power again until the fuel tank is

 closed and safe.

 (b)  
Disconnect the battery and attach a sign that shows OPEN FUEL TANKS - DO NOT CONNECT.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH THE SURGE TANK FLAME ú

 28-13-31
 ARRESTER  ú
 ú 01 ú BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.  Page 401Mar 12/01 

A
737-300/400/500MAINTENANCE MANUAL
VENT SCOOP FLAME ARRESTER DOOR NO. 14
SEE C PRESSURE RELIEF VALVE DOOROUTBOARD FWD NO. 13
NO. 2 TANK SEE B
SEE A
OUTBOARD NO. 2 TANK
A
PRESSURE RELIEF VALVE PRESSURE RELIEF VALVE DOOR NO. 13 DOOR NO. 13 (KNOB TYPE) (T-HANDLE TYPE)
BB
SEE D
VENT SCOOP FLAME
ARRESTER DOOR NO. 14

C

Air Vent Scoop Flame Arrester Installation
Figure 401 (Sheet 1)

K34434
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. AIRPLANES WITH THE SURGE TANK FLAME ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 燃油 FUEL 2(7)