(b)
 If the fault does not continue:

 -refer to Para. 4.B.
 B. Install the BMC2 (1HA2) (Ref. AMM TASK 36-11-34-400-001) and do the test given in Para. 3.
 1
 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page B211
 --Feb 01/05R ---CES -

 Abnormal Bleed Temperature Shown Amber during BMC2 Test with the Engines Not in Operation
 1. Possible Causes
_______________
 -BMC-2 (1HA2)
 -SENSOR-EXCHANGER OUT TEMP, ENG 2 (6HA2)
 -
wiring from the connector 1HA2-AB/1B to the ground

 -
wiring from the connector 1HA2-AA/9B to the connector 6HA2-A/2

 -
wiring from the connector 1HA2-AA/10B to the connector 6HA2-A/4

 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice(s)
 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 36-11-00-740-001 BITE Test of the BMC 1(2) AMM 36-11-17-000-001 Removal of the Heat-Exchanger Outlet-Temperature Sensor 6HA1(6HA2) AMM 36-11-17-400-001 Installation of the Heat-Exchanger Outlet-Temperature
 Sensor 6HA1(6HA2) AMM 36-11-34-000-001 Removal of the BMC (1HA1, 1HA2) AMM 36-11-34-400-001 Installation of the BMC (1HA1, 1HA2) ASM 36-11/02
 3. Fault Confirmation
__________________
 A. Job Set-Up
 (1) On the center pedestal, on the ENG panel 115VU:
 -put a warning notice(s) to tell persons not to start the engines.
 B. Test
 (1) Do the BITE test of the BMC2 (Ref. AMM TASK 36-11-00-740-001).
 1
 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page B212
 --Feb 01/05R ---CES -

 4. Fault Isolation
_______________

 A. If during the test with the engines not in operation, an abnormal bleed temperature is shown amber on the BLEED page of the lower ECAM DU:
 -remove the BMC1 (1HA1) (Ref. AMM TASK 36-11-34-000-001)
 -Do the test given in para. 3.
 (1) If during the test, the abnormal bleed temperature is shown amber on the BLEED page for the engines 1 and 2: - on the connector 1HA2-AB, on the wiring side, make sure that there
 is ground at pin 1B (Ref. ASM 36-11/02):
 (a)
 If there is ground at pin 1B:

 -replace the BMC-2 (1HA2) (Ref. AMM TASK 36-11-34-000-001) and (Ref. AMM TASK 36-11-34-400-001)
 -refer to Para. 4.B.

 (b)
 If there is no ground at pin 1B:

 -do a check and repair the wiring from the connector 1HA2-AB/1B to the ground
 -refer to Para. 4.B.
 (2) If during the test, the abnormal bleed temperature is shown amber on the BLEED page for the engine 2 only:
 -replace the SENSOR-EXCHANGER OUT TEMP, ENG 2 (6HA2) (Ref. AMM TASK 36-11-17-000-001) and (Ref. AMM TASK 36-11-17-400-001).
 (a)
 If the fault continues:

 -do a check and repair the wiring from the connector 1HA2-AA/9B to the connector 6HA2-A/2 and wiring from the connector 1HA2-AA/10B to the connector 6HA2-A/4 (Ref. ASM 36-11/02)
 -refer to Para. 4.B.

 (b)
 If the fault does not continue:

 -refer to Para. 4.B.
 B. Install the BMC1 (1HA1) (Ref. AMM TASK 36-11-34-400-001) and do the test given in Para. 3.
 1
 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page B213
 --Feb 01/05R ---CES -

R **ON A/C 151-199, 401-499,
 TASK 36-11-00-810-930
 BMC1 output failure for HP Bleed Override Solenoid of Engine 1

 1. Possible Causes
_______________
 -BMC-1 (1HA1)
 -SOL-HP BLEED OVERRIDE, ENG1 (11HA1)
 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
AMM 36-11-00-740-001 BITE Test of the BMC 1(2)
 AMM 36-11-34-000-001 Removal of the BMC (1HA1, 1HA2)
 AMM 36-11-34-400-001 Installation of the BMC (1HA1, 1HA2)
　
中國(guó)航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊(cè) PNEUMATIC(90)