(b)
 Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only) (Ref. AMM TASK 31-60-00-860-001).

 B. Test
 (1) Do a check of the position of the ENG 1 BLEED pushbutton switch (4HA1).
 (a) If the pushbutton switch is pushed:
 - on the ECAM control panel 11VU, push the BLEED key (the BLEED page comes into view on the lower ECAM DU)
 -approximately 30 minutes after engine 1 shutdown, do a check of the position of the bleed pressure regulator valve (4001HA) on the BLEED page.
 NOTE : During the engine shutdown, the bleed pressure regulator
____
 valve can close slowly, without closure command. The cause
 of this slow closure can be a decreased segmentation play.
 1_ If the position is fully closed:
 - no more maintenance is necessary.
 2_ If the position is not fully closed:
 - do the trouble shooting given in Para. 4.A.

 (b) If the pushbutton switch is released: 1 Connect the TEST SET - ENGINE BLEED SYSTEM (98D36003000000) or
_ TEST SET - ENGINE BLEED SYSTEM (98F36003002000) to the test port of the bleed pressure regulator valve, and slowly pressurize the system No. 2 to 30 psi (2.0684 bar).
 2 On the ECAM control panel 11VU, push the BLEED key (the BLEED
_ page comes into view on the lower ECAM DU).
 3 On the AIR COND panel 30VU, make sure that the ENG 1 BLEED
_ pushbutton switch (4HA1) is pushed.
 4 On the BLEED page, make sure that the bleed pressure regulator
_ valve is shown open.
 1
 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 228
 --Feb 01/05R ---CES -

 5_ Start the APU:
 - GTCP 36-300 (Ref. AMM TASK 49-00-00-860-003)
 or
 - APS 3200 (Ref. AMM TASK 49-00-00-860-005)
 or
 - 131-9(A) (Ref. AMM TASK 49-00-00-860-008).

 6 On the AIR COND panel 30VU, push the APU BLEED pushbutton
_ switch (the OFF legend goes off).
 7 On the BLEED page, make sure that the bleed pressure regulator
_ valve is shown closed.
 8 Stop the APU:
_
 -GTCP 36-300 (Ref. AMM TASK 49-00-00-860-004) or
 -APS 3200 (Ref. AMM TASK 49-00-00-860-006) or
 -131-9(A) (Ref. AMM TASK 49-00-00-860-009).
 9 Depressurize the system on the test set.
_
 10 Remove the TEST SET - ENGINE BLEED SYSTEM (98D36003000000) or
__ TEST SET - ENGINE BLEED SYSTEM (98F36003002000).
 4. Fault Isolation
_______________
 A. Do a check of the visual position indicator of the bleed pressure regulator valve.
 (1) If the visual position indicator is in the closed position:
 -disconnect the electrical connector 4001HA1-A and make sure that there is continuity between pin A/5 and A/3.
 (a) If there is continuity:
 - on the wiring side, do a check for ground at the connector 4001HA1-A pin 3.
 1 If there is a ground signal:
_
 -do a check and repair the wiring from the bleed pressure regulator valve 4001HA1-A pin A/5 and the BMC1 pin AA/2B (Ref. ASM 36-11/01).
 2 If there is no ground signal:
_
 -do a check and repair the wiring from the connector 4001HA1-A pin 3 to the ground point (Ref. ASM 36-11/01).
 (b) If there is no continuity:
 -replace the VALVE-BLEED PRESS REG (4001HA) (Ref. AMM TASK 36-11-52-000-040) and (Ref. AMM TASK 36-11-52-400-040).
 1
 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 229
 --Feb 01/05R ---CES -

 (2) If the visual position indicator is in the open position:
 -disconnect the sense line between the bleed pressure regulator valve and the bleed-pressure-regulated valve-control solenoid.
 (a)
 If the bleed pressure regulator valve is closed:

 -replace the SOLENOID-BLEED PRESS REG V CTL, ENG 1 (10HA1) (Ref. AMM TASK 36-11-55-000-001) and (Ref. AMM TASK 36-11-55-400-001).

 (b)
 If the bleed pressure regulator valve is not closed:

 -replace the VALVE-BLEED PRESS REG (4001HA) (Ref. AMM TASK 36-11-52-000-040) and (Ref. AMM TASK 36-11-52-400-040).
 -refer to Para. 4B.

 (c)
 If the fault continues:

 -replace the P/BSW-ENG 1 BLEED (4HA1).
 1 If the fault continues:
_
 -do a check and repair the wiring (Ref. ASM 36-11/01) between: . pin 2 of the AIR BLEED/ENG 1/CTL circuit breaker (3HA1) and pin AA/8A of the BMC 1 (1HA1) . pin 2 of the AIR BLEED/ENG 1/CTL circuit breaker and pin A/D2 of the ENG 1 BLEED pushbutton switch (4HA1) . pin AA/7A of the BMC 1 and pin A/D1 of the ENG 1 BLEED pushbutton switch . pin A/D3 of the ENG 1 BLEED pushbutton switch and pin A/1 of the engine 1 bleed pressure regulator valve control solenoid (10HA1) . pin A/2 of the engine 1 bleed pressure regulator valve control solenoid and the ground.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 PNEUMATIC(28)