-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 256
 --Feb 01/05R ---CES -

 Loss of the Two Sensing Elements of the Exchanger Outlet Temperature-Sensor of the Engine 2
 1. Possible Causes
_______________
 -SENSOR-EXCHANGER OUT TEMP, ENG 2 (6HA2)
 -BMC-2 (1HA2)
 -BMC-1 (1HA1)
 -
wiring between pin A/1 of the exchanger outlet temperature-sensor (6HA2) and th ground terminal

 -
wiring from the exchanger outlet temperature-sensor (6HA2) to the BMC2 (1HA2)

 -
wiring from the exchanger outlet temperature-sensor (6HA2) to the BMC1 (1HA1)

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 36-11-17-000-001 Removal of the Heat-Exchanger Outlet-Temperature Sensor 6HA1(6HA2) AMM 36-11-17-400-001 Installation of the Heat-Exchanger Outlet-Temperature
 Sensor 6HA1(6HA2) AMM 36-11-34-000-001 Removal of the BMC (1HA1, 1HA2) AMM 36-11-34-400-001 Installation of the BMC (1HA1, 1HA2) ASM 36-11/01 ASM 36-11/02
 3. Fault Confirmation
__________________
 A. Test.
 (1) Not applicable, the fault is evident.
 1
 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 257
 --Feb 01/05R ---CES -

 4. Fault Isolation
_______________

 A. If the fault symptom is identified by the maintenance message: TEMP SENSOR 6HA2:
 -replace the SENSOR-EXCHANGER OUT TEMP, ENG 2 (6HA2) (Ref. AMM TASK 36-11-17-000-001) and (Ref. AMM TASK 36-11-17-400-001).
 (1)
 If the fault continues:

 -do a check for ground at pin A/1 of the exchanger outlet temperature-sensor (6HA2)
 (a)
 If there is no ground:

 -do a check and repair the wiring between pin A/1 of the exchanger outlet temperature-sensor (6HA2) and th ground terminal (Ref. ASM 36-11/02).

 (b)
 If there is ground:

 -
do a check and repair the wiring from the exchanger outlet temperature-sensor (6HA2) to the BMC2 (1HA2), pins A/2 and A/4 to pins AA/9B and AA/10B and

 -
do a check and repair the wiring from the exchanger outlet temperature-sensor (6HA2) to the BMC1 (1HA1), pins A/4 and A/5 to pins AA/6D and AA/7D (Ref. ASM 36-11/01).

 (2)
 If the fault continues:

 -replace the BMC-2 (1HA2) and/or the BMC-1 (1HA1) (Ref. AMM TASK 36-11-34-000-001) and (Ref. AMM TASK 36-11-34-400-001).
 B. After the subsequent flight, make sure that the fault does not continue.
 1
 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page 258
 --Feb 01/05R ---CES -

 Loss of the Non Return Function and Temperature Limitation Function of the Bleed Pressure-Regulator Valve of the Engine 1
 1. Possible Causes_______________
 -VALVE-BLEED PRESS REG (4001HA)
 -SOLENOID-BLEED PRESS REG V CTL, ENG 1 (10HA1)
 2. Job Set-up Information______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
AMM 36-11-00-740-001  BITE Test of the BMC 1(2)
 AMM 36-11-52-000-040  Removal of the Bleed Pressure-Regulator Valve (4001HA)
 AMM 36-11-52-400-040  Installation of the Bleed Pressure-Regulator Valve (4001HA)
 AMM 36-11-52-720-001  Functional Test of the Opening of the Bleed Pressure Regulator Valve
 AMM 36-11-55-000-001  Removal of the Bleed-Pressure-Regulator Valve Control-Solenoid (10HA1,10HA2)
 AMM 36-11-55-400-001  Installation of the Bleed-Pressure-Regulator Valve Control-Solenoid (10HA1,10HA2)
 3. Fault Confirmation__________________
 A. Test
 (1)
 Do the operational test of the BMC1 (with the CFDS) (Ref. AMM TASK 36-11-00-740-001).

 (2)
 Do the test of the bleed pressure-regulator valve (Ref. AMM TASK 36-11-52-720-001).

 4. Fault Isolation_______________
 A. If the test gives the maintenance message:
 PRESS REG-V 4001HA1 OR SOL 10HA1 OR SENSE LINE:
　
中國(guó)航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊(cè) PNEUMATIC(38)