R APU and Crossbleed Air Supply - Block Diagram Figure 301
 1
 -EFF : ALL

-∞∞36-12-00∞∞∞∞∞∞∞∞∞∞Page 302
 --May 01/99 ---CES - TASK 36-22-00-810-801

 Air Leak in the Left Wing
 1. Possible Causes
_______________
 -ducts
 -seal
 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R AMM 36-11-00-720-004 Leak Check of Engine Bleed Air Supply System AMM 36-11-17-000-001 Removal of the Heat-Exchanger Outlet-Temperature Sensor 6HA1(6HA2) AMM 36-11-17-400-001 Installation of the Heat-Exchanger Outlet-Temperature Sensor 6HA1(6HA2)
 3. Fault Confirmation
__________________
 A. Test
 (1) Do the functional test of the engine bleed-air supply-system (Ref. AMM TASK 36-11-00-720-004).
 4. Fault Isolation
_______________
 A. Make sure that the leak is on the same side of the leak warning.
 (1) Repair the ducts which cause the leak.
 NOTE : If the L WING LEAK ECAM warning comes into view on ground and
____
 if:

 -the packs are in operation

 -there is high OAT

 -you replaced the flow control valve (8HB)
 first do a check of the pack area or of the seals at the flow
 control valve.

 (a) If no leak is found on the wing ducts: - open the access door 471AL on the pylon
 -remove the engine 1 exchanger outlet temperature sensor (6HA1) (Ref. AMM TASK 36-11-17-000-001)
 1 -EFF : ALL

-∞∞36-22-00∞∞∞∞∞∞∞∞∞∞Page 201

 --Aug 01/05 ---CES -

 -make sure that the seal of the engine 1 exchanger outlet temperature sensor (6HA1) is not damaged. Replace the seal if necessary
 -install the engine 1 exchanger outlet temperature sensor (6HA1)
 (Ref. AMM TASK 36-11-17-400-001) R - close the access door 471AL.
 B. After the subsequent flight, make sure that the fault does not continue.
 1 -EFF : ALL

-∞∞36-22-00∞∞∞∞∞∞∞∞∞∞Page 202
 --May 01/05 ---CES - Air Leak in the Right Wing

 1. Possible Causes
_______________
 -ducts
 -seal
 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R AMM 36-11-00-720-004 Leak Check of Engine Bleed Air Supply System AMM 36-11-17-000-001 Removal of the Heat-Exchanger Outlet-Temperature Sensor 6HA1(6HA2) AMM 36-11-17-400-001 Installation of the Heat-Exchanger Outlet-Temperature Sensor 6HA1(6HA2)
 3. Fault Confirmation
__________________
 A. Test
 (1) Do the functional test of the engine bleed-air supply-system applicable to the right wing only (Ref. AMM TASK 36-11-00-720-004).
 4. Fault Isolation
_______________
 A. Make sure that the leak is on the same side of the leak warning.
 (1) Repair the ducts which cause the leak.
 NOTE : If the R WING LEAK ECAM warning comes into view on ground and
____
 if:

 -the packs are in operation

 -there is high OAT

 -you replaced the flow control valve (11HB)
 first do a check of the pack area or of the seals at the flow
 control valve.

 (a) If no leak is found on the wing ducts: - open the access door 482AR on the pylon
 -remove the engine 2 exchanger outlet temperature sensor (6HA2) (Ref. AMM TASK 36-11-17-000-001)
 -make sure that the seal of the engine 2 exchanger outlet temperature sensor (6HA2) is not damaged. Replace the seal if necessary
 1 -EFF : ALL

-∞∞36-22-00∞∞∞∞∞∞∞∞∞∞Page 203

 --Aug 01/05 ---CES -

 -install the engine 2 exchanger outlet temperature sensor (6HA2)

 (Ref. AMM TASK 36-11-17-400-001) R - close the access door 482AR.
 B. After the subsequent flight, make sure that the fault does not continue.
 1 -EFF : ALL

-∞∞36-22-00∞∞∞∞∞∞∞∞∞∞Page 204
 --May 01/05 ---CES - Air Leak in the Engine 1 Pylon
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 PNEUMATIC(111)