-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page A285
 --Feb 01/05R ---CES -

 The Bleed Pressure-Regulator Valve of the Engine 2 is Shown Closed Amber on the Lower ECAM DU
 1. Possible Causes_______________
 -XDCR-BLEED TRANSFER PRESS, ENG 2 (7HA2)
 -VALVE-BLEED PRESS REG (4001HA)
 -SOLENOID-BLEED PRESS REG V CTL, ENG 2 (10HA2)
 -sense line
 -wiring
 2. Job Set-up Information______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
AMM 36-11-00-720-007  Functional Test of the Sense Lines Upstream of the Bleed Pressure Regulator Valve (4001HA) and Connected to the Control Solenoid (10HA1,10HA2)
 AMM 36-11-00-740-001  BITE Test of the BMC 1(2)
 AMM 36-11-15-000-001  Removal of the Bleed Transferred Pressure Transducer (7HA1,7HA2)
 AMM 36-11-15-400-001  Installation of the Bleed Transferred Pressure Transducer (7HA1,7HA2)
 AMM 36-11-15-720-001  Functional Test of the Bleed Transferred Pressure Transducer (7HA1,7HA2)
 AMM 36-11-52-000-040  Removal of the Bleed Pressure-Regulator Valve (4001HA)
 AMM 36-11-52-400-040  Installation of the Bleed Pressure-Regulator Valve (4001HA)
 AMM 36-11-55-000-001  Removal of the Bleed-Pressure-Regulator Valve Control-Solenoid (10HA1,10HA2)
 AMM 36-11-55-400-001  Installation of the Bleed-Pressure-Regulator Valve Control-Solenoid (10HA1,10HA2)
 ASM 36-11/02
 TSM 36 PB 101
 3. Fault Confirmation__________________
 A. Test
 (1) Do the BITE test of the BMC2 (Ref. AMM TASK 36-11-00-740-001).
 1
 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page A286
 --Feb 01/05R ---CES -

 4. Fault Isolation
_______________

 A. If the test gives a maintenance message, you can find the related trouble shooting procedure in the (Ref. TSM 36 PB 101).
 (1) If there is no maintenance message:
 -do the functional test of the bleed transferred pressure transducer (7HA2) (Ref. AMM TASK 36-11-15-720-001)
 (a)
 If the test is not OK:

 -replace the XDCR-BLEED TRANSFER PRESS, ENG 2 (7HA2) (Ref. AMM TASK 36-11-15-000-001) (Ref. AMM TASK 36-11-15-400-001).

 (b)
 If the test is OK:

 -replace the VALVE-BLEED PRESS REG (4001HA) (Ref. AMM TASK 36-11-52-000-040) and (Ref. AMM TASK 36-11-52-400-040).
 1_ If the fault continues:
 - replace the SOLENOID-BLEED PRESS REG V CTL, ENG 2 (10HA2)
 (Ref. AMM TASK 36-11-55-000-001) and (Ref. AMM TASK 36-11-
55-400-001).

 a If the fault continues:
_
 -do the functional test of the upstream sense line between the bleed pressure-regulator valve (4001HA) and the control solenoid (10HA2) (Ref. AMM TASK 36-11-00-720-007).
 *
 If the pressure decreases to 0 psig in less than 20
 seconds:
 ** replace the related sense line.

 *
 If the pressure drop is not high:
 ** do a check and repair the wiring:
 . from the FULLY CLOSED signal of the BMC2 (1HA2) to the
 bleed pressure-regulator valve (4001HA)
 . from pin A/5 of the bleed pressure-regulator valve
 (4001HA) to the first terminal block (Ref. ASM 36-11/02).

 B. After the subsequent flight, make sure that the fault does not continue.
 1
 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page A287
 --Feb 01/05R ---CES -

 The HP Bleed Valve of the Engine 2 is Shown Closed Amber on the Lower ECAM DU
 1. Possible Causes
_______________
 -VALVE-HP BLEED (4000HA)
 -VALVE-BLEED PRESS REG (4001HA)
 -sense line
 -wiring
 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 36-11-00-720-007  Functional Test of the Sense Lines Upstream of the Bleed Pressure Regulator Valve (4001HA) and Connected to the Control Solenoid (10HA1,10HA2)
 AMM 36-11-00-740-001 BITE Test of the BMC 1(2)
 AMM 36-11-51-000-040 Removal of the High Pressure Bleed Valve (4000HA)
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 PNEUMATIC(82)