(1)
 Do the engine start procedure.

 (2)
 Make sure that the ECAM warning AIR ENG 2 BLEED FAULT is not shown on the upper ECAM DU.

 1
 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page A226
 --Feb 01/05R ---CES -

 Loss of or Accidental Automatic Closure of the Bleed Pressure-Regulator Valve of the Engine 1
 1. Possible Causes
_______________

 -SOLENOID-BLEED PRESS REG V CTL, ENG 1 (10HA1)
 -P/BSW-ENG 1 BLEED (4HA1)
 -AIR BLEED/ENG 1/CTL (3HA1)
 -BMC-1 (1HA1)
 -wiring

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
R 24-00-00-810-803 Circuit Breaker Tripped and/or C/B TRIPPED Warning AMM 36-11-00-740-001 BITE Test of the BMC 1(2) AMM 36-11-34-000-001 Removal of the BMC (1HA1, 1HA2) AMM 36-11-34-400-001 Installation of the BMC (1HA1, 1HA2) AMM 36-11-55-000-001 Removal of the Bleed-Pressure-Regulator Valve Control-Solenoid (10HA1,10HA2) AMM 36-11-55-400-001 Installation of the Bleed-Pressure-Regulator Valve Control-Solenoid (10HA1,10HA2) ASM 36-11/01
 3. Fault Confirmation
__________________
 A. Test

 (1) Do the BITE test of the BMC1 (Ref. AMM TASK 36-11-00-740-001).
 4. Fault Isolation
_______________

 A. Table of the circuit breakers used in this procedure:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU AIR BLEED/ENG 1/CTL 3HA1 D12 49VU AIR BLEED/ENG 1/MONG 2HA1 D11
 1 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page A227
 --May 01/05 ---CES -

R  B. If the test gives the maintenance message: 
R  BMC1 OR SOLENOID 10HA1 CKT 
R  NOTE : If the maintenance message BMC1 OR SOLENOID 10HA1 CKT comes into____ 
R  view with no associated ECAM warning, no trouble shooting 
R  procedure is necessary. 
R  - Do a check of the status of the circuit breaker (3HA1). 
R  (1) If the circuit breaker (3HA1) is closed: 
R  - Do a check for 28 VDC at pin A/1 of the connector of the bleed 
R  pressure regulator valve control solenoid (10HA1) with the ENG 1 
R  BLEED pushbutton switch (4HA1) released (OFF legend on). 
R  (a) If there is 28 VDC: 
R  - Do a check for ground at pin A/2 of the connector of the bleed 
R  pressure regulator valve control solenoid (10HA1). 
R  1_  If there is no ground signal:
R  - Repair the wiring from the pin A/2 to the ground point. 
R  2_  If there is a ground signal:
R  - Replace the SOLENOID-BLEED PRESS REG V CTL, ENG 1 (10HA1) 
R  (Ref. AMM TASK 36-11-55-000-001) and (Ref. AMM TASK 36-11-
R  55-400-001). 
R  (b) If there is no 28 VDC: 
R  - Do a check for 28 VDC at pin A/D2 of the ENG 1 BLEED pushbutton 
R  switch (4HA1). 
R  1_  If there is 28 VDC:
R  - Replace the P/BSW-ENG 1 BLEED (4HA1). 
R  a_  If the fault continues:
R  - Do a check and repair the wiring from the pin A/1 of the 
R  bleed pressure regulator valve control solenoid to the 
R  pin A/D3 of the ENG 1 BLEED pushbutton switch. 
R  2_  If there is no 28 VDC:
R  - Do a check and repair the wiring from the pin A/D2 of the 
R  ENG 1 BLEED pushbutton switch to the pin 2 of the circuit 
R  breaker 3HA1. 
R  a_  If the fault continues:
R  - Replace the AIR BLEED/ENG 1/CTL (3HA1). 
R  (2) If the circuit breaker (3HA1) is tripped: 
R  - Do the procedure (Ref. TASK 24-00-00-810-803).

 1 -EFF : ALL

-∞∞36-11-00∞∞∞∞∞∞∞∞∞∞Page A228
 --Feb 01/05 ---CES -

R  (3) Check of the automatic closure of the bleed pressure regulator valve 
R  (4001HA). 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 PNEUMATIC(62)