B. DAN132
(1)
P/N Identification
DAN132 -02 | | | ------------------- Diameter code ---------------------------- Standard P/N
(2)
P/N Characteristics
(a)
Temperature Minimum operating temperature is -55 deg.C (-67.00 deg.F). Maximum operating temperature is 220 deg.C (428.00 deg.F). Shrinkage temperature is 175 deg.C (347.00 deg.F).
(b)
Diameter code and shrinking tools
(Ref. Fig. 009)
20-42-12 Page 15
Shrink Sleeves - Shrinking Tools and Allocation Table for Wires
E0484
Figure 008
20-42-12 Page 16
Apr 01/05
R
Shrink Sleeves - P/N Characteristics and Shrinking Tools
DAN132
Figure 009
20-42-12 Page 17
Apr 01/05
R
C. NSA937210
(Ref. Fig. 010, 011, 012)
(1)
P/N identification
NSA937210 - MB01 00 | | | | | -------------- length (mm) | ------------------- Diameter code ---------------------------- Standard P/N
(2)
Characteristics
(a)
Temperature Minimum operating temperature is -67 deg.C (-88.60 deg.F). Maximum operating temperature is 250 deg.C (482.00 deg.F). Shrinkage temperature is 327 deg.C (620.60 deg.F).
(b)
Length
------------------------------| Length code | Length in mm | |-------------|--------------| | 00 | 1200 | |-------------|--------------| | 30 | 30 | |-------------|--------------| | 40 | 40 | |-------------|--------------| | 50 | 50 | |-------------|--------------| | 60 | 60 | ------------------------------
(c)
Diameter code and shrinking tools (Ref. Fig. 010)
(3)
Shield stop procedure
(Ref. Fig. 010)
R (a) Cut and remove the insulation to get the dimension B.
R (b) Move the shield rearward on the insulation.
R (c) Install the heat shrink sleeve.
(d) Heat shrink the sleeve.
20-42-12 Page 18
Shrink Sleeves - P/N Characteristics and Shrinking Tools
NSA937210
Figure 010
20-42-12 Page 19
Apr 01/05
R
Shrink Sleeves - Allocation Table for Wires
NSA937210
Figure 011
20-42-12 Page 20
Apr 01/05
R
Shrink Sleeves - Allocation Table for Wires
NSA937210 and NSA937493
Figure 012
20-42-12 Page 21
Apr 01/05
R
D. NSA937493
(Ref. Fig. 012)
(1)
P/N Identification
NSA937493 - 001 | | | ------------------- Diameter code ---------------------------- Standard P/N
(2)
P/N Characteristics
(a) Temperature Minimum operating temperature is -55 deg.C (-67.00 deg.F). Maximum operating temperature is 260 deg.C (500.00 deg.F). Shrinkage temperature is 327 deg.C (620.60 deg.F).
(b) Length R Supplied by lengths or in cut sleeves, maximum length variation R 20%.
(c) Diameter code and shrinking tools
(Ref. Fig. 013)
20-42-12 Page 22
Shrink Sleeves - Shrinking Tools and Allocation Table for Wires
NSA937493
Figure 013
20-42-12 Page 23
____________________________________
END CAPS - DESCRIPTION AND OPERATION
R R R R R _______1. General End caps are used to isolate the end of a cable that is not connected. High and low temperature end caps installed on aircraft have the codes that follow: - NSA936601 sealing end cap, high temperature NSA936604 sealing end cap, low temperature - ABS0065 heat shrinkable end cap NSA936603 heat shrinkable end cap
________________2. Sealing End Caps
A. NSA936601
R R (1) P/N identification NSA936601 CA 11 12 | || | | | || | ------------ Max. permitted dia. in 1/10 mm | || | | || ---------------- Min. permitted dia. in 1/10 mm | || | |------------------- Type code | | | -------------------- Cap | --------------------------- Standard P/N
(2) P/N characteristics
(a) Temperature Maximum operating temperature is 250 deg.C (482.00 deg.F).
(b) Color identification (Ref. Fig. 001)
R R (3) Allocation table (Ref. Fig. 002) This table gives the size of the cap to use for the wire type and gauge.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 2(89)
