R ED-7-CONT-230/110V R Figure 004
20-25-32 Page 8
Infrared Generators - Description IR1759 and IR3104 R Figure 005
20-25-32 Page 9
----------------------------------------------------------------------------| | GUN | REFLECTOR | LAMP | |MANUFACTURER|---------------------------|With clamps|-----------------------| | | P/N |SUPPLY|POWER| P/N | P/N |SUPPLY |POWER| | | | (V) | (W) | | | (V) | (W) | |------------|---------- ---|--- --|-----|-----------|-------|-------| ----| | |IR-3104-MK2/A | 24 | 250 | AT-3147 | | | | | |--------------|------|-----|-----------| | | | | RAYCHEM | IR-3104-MK31 | 24 | 250 |AT-3147MK31|NAE-143-3| 24 | 250 | | |--------------|------|-----|-----------| | | | | | IR-3104-MK3 | 24 | 250 |AT-3147MK3 | | | | ----------------------------------------------------------------------------
B. Type IR1759 R Standard opening:
-
Max. dia. 9 mm (0.3543 in.)
-
Max. length 30 mm (1.1811 in.)
----------------------------------------------------------------------------
| | GUN | REFLECTOR | LAMP |
|MANUFACTURER|---------------------------|With clamps|-----------------------|
| | P/N |SUPPLY|POWER| P/N | P/N |SUPPLY |POWER|
| | | (V) | (W) | | (V) | (W) | (W) |
|------------|---------- ---|--- --|-----|-----------|-------|-------| ----|
| |IR-1759-MK2/A | 24 | 250 | AT-3132 | | | |
| |--------------|------|-----|-----------| | | |
| RAYCHEM | IR-1759-MK31 | 24 | 250 |AT-3132MK31|NAE-143-3| 24 | 250 |
| |--------------|------|-----|-----------| | | |
| | IR-1759-MK3 | 24 | 250 |AT-3132MK3 | | | |
----------------------------------------------------------------------------
___________________
4. Operating procedure R (Ref. Fig. 006)
____
NOTE : Make sure that you always keep the reflectors or mirrors of the infrared generator clean, to make sure that heating is constant.
-Put the generator selector in Auto position.
-Adjust the generator to agree with the generator type and the sleeve.
-Choose the gun and the reflector to agree with the solder sleeve.
-Push the reflector trigger and engage the wires and the slevee in the reflector.
-Make sure that the assembly is in the correct position.
-Turn the soldering on to the infrared source.
-Push the trigger of the infrared gun to start. The gun stops automatically at the end of the cycle.
-After 3 to 5 seconds, remove the wire assembly.
-Make sure that the solder sleeve is correctly shrunk.
20-25-32 Page 10
Infrared Generators - Operating Procedure R Figure 006
20-25-32 Page 11
______________________________________________________
INSERTION/EXTRACTION TOOLS - DESCRIPTION AND OPERATION
_______1. General The chapters that follow give description and operation of insertion/extraction tools.
_________________________2. Structure of the Chapters
R R A. General Requirements for Contact Insertion/Extraction Tools (Ref. 20-25-41).
R R B. Contact Insertion/Extraction Tools (Ref. 20-25-42).
20-25-40 Page 120-25-41 Page 1
R R ___________________________________________________________GENERAL REQUIREMENTS FOR CONTACT INSERTION/EXTRACTION TOOLS _________________________DESCRIPTION AND OPERATION
R R _______1. General
R R This topic gives the requirements and the processes to insert/extract the removable contacts used on aircraft.
R
R R R __________2. Definition (Ref. Fig. 001) The removable contacts have to be correctly positioned and locked in connecting elements to secure reliable electrical connections.
R ______________________________3. Insertion of Contact with Tool (Ref. Fig. 002) Select the tool to suit the type and size of contact (Ref. 20-48-XX).
____NOTE : To facilitate insertion of the contacts in the modules/connectors and to improve the check made on the locking of each contacts, twisted wires must be untwisted over a lenght of 60 mm (2.3622 in.) before connecting to connectors or modules.
For a plastic or metal tool, pen type : - take the colored end, - with your thumb, slide the cable into the opening, - apply slight tension so that the collar of the contact bears on the front of the tool, - stop all relative movement by gripping the cable between your thumb and the anti-slip portion of the tool. For other tools :
- install the wired contact in the tool, - position the contact in line with the cavity, - push forward. When the collar passes through the clip, a small click may be heard and the locking felt, - free the cable by releasing the pressure, - remove the tool from the cavity by pulling rearwards ; the tool slides over the
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 2(7)
