------------------------------- Standard P/N
 (2)
 P/N characteristics

 (a) Temperature Minimum operating temperature is -55 deg.C (-67.00 deg.F) Maximum operating temperature is 175 deg.C (347.00 deg.F)

 (3)
 Installation procedure

 -Install the backshell on the wires before you connect them to the connector.
 -Screw the backshell on the connector.
 -Tighten the backshell with pliers UTICA 529 or equivalent.
 ____
NOTE : To make the tightening of the backshell easier you can use a tightening support SOURIAU 580030 or equivalent.
 -If necessary, safety the connector (ref 20-51-12).
 -You can wind silicone tape NSA935403 around cable bundles for small diameters to make up for differences in diameter.
 -Attach the bundle to the backshell with the clamp.
 C. NSA938003 threads Protector (Ref. Fig. 001)
 (1) P/N identification
 NSA938003  -10 | | | ----------------- Type code | -------------------------- Standard P/N

20-33-45 Page 4
 Apr 01/03
R  ___________________________________

3. Backshell for Rectangular Connector
 This type of backshell has for example the codes that follow:

 -Assembly by clips: E0312 backshell for MIL-C-24308 (E0237, E0362) connector type. E0393 backshell for PREN3545 (E0390) connector type. EN3545-007 backshell for PREN3545 connector type. ABS0364-C backshell for ABS0364-A and ABS0364-B connector. ABS1019-005 backshell for ABS1019-003 and ABS1019-004 connector.
R
 -
Assembly by screws: ABS0388 backshell for MIL-C-24308 (E0237) connector type. ABS0699 backshell for MIL-C-24308 (ABS0713, E0237 and E0302) connector type. ABS0700 backshell for MIL- C-24308 (E0237) connector type. E0365 backshell for MIL-C-24308 (E0237, E0362 and NSA938361) connector type. E0448 backshell for MIL- C-24308 (E0237, E0362) connector type. NSA938422 backshell for MIL-C-24308 (E0237, E0362, E0302, NSA938361) connector type.

 A.
 Backshell assembly by clips (E0312, E0393, EN3545-007, ABS0364-C and ABS1019-005)

 (1)
 P/N identification
 (Ref. Fig. 002)

 Example :  E0393 D 01 | | | | | -------------------- Type code | | | ------------------------ Size code | ----------------------------- Standard P/N

 (2)
 P/N characteristics

 (a) Temperature Minimum operating temperature is -55 deg.C (-67.00 deg.F) Maximum operating temperature is 125 deg.C (257.00 deg.F)

 (3)
 Installation procedure
 (Ref. Fig. 002, 003, 004)

 -Install the backshell on the wires before you connect them to the connector
 -Insert the backshell on the connector in compliance with the orientation. Only for E0393 and EN3545-007:

20-33-45 Page 5

R Backshell, End Piece and Conduit Fitting - P/N Characteristics and Installation E0393 and EN3545-007 Figure 002

20-33-45 Page 6

R Backshell, End Piece and Conduit Fitting - P/N Characteristics and Installation R ABS0364-C and ABS1019-005
 Figure 003

20-33-45 Page 7

R Backshell, End Piece and Conduit Fitting - P/N Characteristics and Installation E0312 Figure 004

20-33-45 Page 8

 -
In vertical position, make sure that the N.1 contact is positioned on the bottom left and the backshell on the right (viewed from the front connector).

 -
In horizontal position, make sure that the N.1 contact is located on the top left and the backshell on the bottom (viewed from the front connector). Only for ABS0364-C and ABS1019-005: (Ref. Fig. 003) When this type of connector is assembled, particular attention must be given to the backshell installation If installed properly, the strain relief is easily pushed into the groove and noticeably engages at the end. If not installed properly, a slight resistance is noticeable over the entire insertion length. In addition, the wires are pushed sideways, away from the connector axis.

 -Attach the bundle to the backshell with a cable tie NSA935401.
 B. Backshell assembly by screws (ABS0388, ABS0699, ABS0700, E0365, E0448 and NSA938422)
 (1) P/N identification (Ref. Fig. 005)
 Example : ABS0388  A  15  A
 |  |  |  |
 |  |  |  ---------------- Provisioning code :
 |  |  |  A = with cable tie
 |  |  |  No code = without cable tie
 |  |  |
 |  |  -------------------- Size code (09 to 50)
 |  |
 |  ------- ----------------- Type code : A = 15. angle
 |  B = straight
　
中國(guó)航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 ESPM Electrical Standard Practices Manual 2(82)