F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------122VU ANTI ICE/PROBES/2/PITOT 3DA2 Y14 122VU ANTI ICE/PROBES/2/AOA 4DA2 Y13 122VU ANTI ICE/PROBES/2/PHC 2DA2 Y12 122VU ANTI ICE/PROBES/2/STATIC 5DA2 Y11 122VU ANTI ICE/PROBES/3/PITOT 3DA3 Z16 122VU ANTI ICE/PROBES/3/AOA 4DA3 Z15 122VU ANTI ICE/PROBES/3/STATIC 5DA3 Z14 122VU ANTI ICE/PROBES/1/STATIC 5DA1 Z13 122VU ANTI ICE/PROBES/1/TAT 1DA1 Z12
R **ON A/C 001-049, 051-052, 054-056, 058-059, 061-099, 101-101, 103-149, R 151-199, 201-299, 301-399, 401-499, Post SB 30-1037 For A/C 001-049,051-052,054-056,
122VU ANTI ICE/RAIN/RPLNT/F/O 1DB2 W11
**ON A/C ALL
Subtask 71-00-00-869-096
E. Continue to prepare for test
(1) Do the EIS start procedure (Ref. TASK 31-60-00-860-001) .
(2) Make sure that fire-fighting personnel is there.
(3) On the lower ECAM display unit:
CAUTION : MAKE SURE THAT THE HYDRAULIC RESERVOIR PRESSURE IS IN THE
_______ CORRECT OPERATION RANGE BEFORE YOU START THE ENGINE. THE HYDRAULIC FLUID IS NECESSARY TO LUBRICATE THE HYDRAULIC PUMPS THAT THE ENGINE OPERATES.
(a) Get the HYDRAULIC page.
(b) Make sure that the pressure of the Green reservoir for the engine 1 (Yellow reservoir for the engine 2) is correct.
(c) Make sure that the reservoir fluid level is correct.
(4) Make sure that the engine 1(2) pump is serviceable (on the ENG panel 40VU, the OFF legend of the ENG 1(2) PUMP pushbutton switch must be off).
F 『 EEFF : ALL E Page 54471-00-00
E E Aug 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
Subtask 71-00-00-710-074
F. Do the operational test of the engine fire and overheat detection (loop/squib) (Ref. TASK 26-12-00-710-001).
Subtask 71-00-00-869-097
G. Continue to prepare for test
(1) On the RUD TRIM/PARKING BRK panel 110VU:
(a) Make sure that the parking-brake control switch is set to ON.
(2) On the ENG panel 115VU:
(a) Make sure that the ENG/MASTER 1(2) control switch is set to OFF.
(3) Make sure that the throttle control lever of the engine 1(2) is in the idle stop position (zero on the graduated sector).
(4) On the center instrument panel 400VU, make sure that:
(a) The brake pressure indication on the brake Yellow-pressure triple-indicator is correct. If necessary, pressurize the brake accumulator with Yellow Pump (Ref. TASK 29-10-00-863-002).
(b) The landing-gear normal control-lever is in the DOWN position.
(5) Make sure that the interphone system operates correctly.
(6) Make sure that the aircraft is cleared and that no one stays in the dangerous areas.
(7) On the lower ECAM display unit:
(a) Get the FUEL page. Make sure that there is the correct quantity of fuel in the fuel tanks to run the engine.
(8) On the ENG panel 40VU:
(a) Push all the FUEL/PUMPS pushbutton switches (the OFF legends of these pushbutton switches go off).
(9) Supply the aircraft pneumatic system from a HP ground power unit or the APU (Ref. TASK 36-12-00-860-001) or (Ref. TASK 36-12-00-860-002).
F 『 EEFF : ALL E Page 54571-00-00
E E May 01/04 ERE ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(10) On the overhead CTL & PNL panel 25VU:
(a) Set the EXT LT/BEACON switch to ON
4. Procedure
_________
Subtask 71-00-00-710-075-A
A. Do this test:
R WARNING : AFTER AN ABORT OF THE ENGINE STARTING SEQUENCE, A DRY CRANK, TO
_______ R REMOVE FUEL VAPOURS, WILL OCCUR, ACCOMPANIED BY ECAM MESSAGE: R - AUTO CRANK IN PROGRESS R ON COMPLETION OF THE DRY CRANK, ALWAYS PUT THE "ENG/MASTER" R SWITCH BACK TO THE "OFF" POSITION WHEN INSTRUCTED BY ECAM R MESSAGE: R - ENG MASTER OFF. R IF YOU ONLY CHANGE THE POSITION OF THE ENGINE MODE SELECTOR R SWITCH (FROM "IGN/START" TO "NORM"), THE FADEC SYSTEM WILL NOT R COMPLETE THE ABORT. THERE IS THUS A RISK THAT THE ENGINE WILL R START. THIS CAN CAUSE INJURIES TO PERSONS.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM 動力裝置 POWER PLANT 1(46)
