(a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 F 『 EEFF : ALL E Page 40171-13-11
 E E Nov 01/02 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 Subtask 71-13-11-010-050
 B. Get Access
 (1) Open the fan cowl doors (Ref. TASK 71-13-00-010-040):
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (2) Put the access platform in position.

 4. Procedure
_________ (Ref. Fig. 401/TASK 71-13-11-991-300) Subtask 71-13-11-020-055
 A. Remove the filler plugs of the hoist points from the fan cowl door . Keep the plugs for installations when the task is completed.
 Subtask 71-13-11-480-054
 B. Installation of the Tooling
 (1) Install the universal attach pads (15) in the hoist points of the fan cowl door (10).

 (2) Attach the SLING - FAN COWL (RSE1113) (5) to the universal attach pads (15).

 Subtask 71-13-11-020-050
 C. Removal of the Fan Cowl CAUTION : DO NOT LIFT OR LOWER THE FAN COWL DOOR AFTER THE REMOVAL OF THE
_______ HINGE BOLTS OR THE UPPER DOOR SEAL MAY BE DAMAGED. MOVE THE DOOR AWAY FROM THE PYLON AFTER THE HINGE BOLTS ARE REMOVED TO AVOID SEAL DAMAGE.
 F 『 EEFF : ALL E Page 40271-13-11
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Fan Cowl Door
 Figure 401/TASK 71-13-11-991-300

 F 『 EEFF : ALL E Page 40371-13-11
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (1) Lift the fan cowl door (10) until the weight of the door is supported by the fan cowl sling (5).

 (2) Remove the cotter pins (40) from the hinge bolts (20).

 (3) Remove the hinge bolts (20), the washers (30), (45), and the nuts (25).

 (4) Remove the fan cowl door (10) from the engine and put it on the DOLLY

 - FAN COWL (RSE1115). Subtask 71-13-11-080-056
 D. Removal of the Tooling
 (1) Remove the SLING - FAN COWL (RSE1113) from the universal attach pads (15).
 (2) Remove the universal attach pads (15) from the fan cowl door (10). Subtask 71-13-11-420-056
 E. Install the filler plugs at the hoist points.
 F 『 EEFF : ALL E Page 40471-13-11
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E

 E 56-5B E
 E E
 TASK 71-13-11-400-041

 Installation of the Fan Cowl Doors
 CAUTION : ADJUST THE FAN COWL DOORS WHEN A NEW FAN COWL IS INSTALLED. IF THE
_______
 FAN COWL DOORS ARE NOT CORRECTLY ADJUSTED THE DOORS CAN OPEN IN
 FLIGHT.

 1. Reason for the Job
__________________
 NOTE : If the fan cowl to be removed has a strake installed, the replacement
____ fan cowl must also have a strake installed. For aircraft A320, strakes must be installed on the inner side only.
R For aircraft A318, A319, A321, strakes must be installed on both R sides.
 NOTE : Engine and Nacelle are 2 ways interchangeable but with condition
____ R (Refer to AI SIL 71-037).
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific universal attach pads
 No specific warning notice
 No specific access platform 1 m (3 ft. 3 in.)
 RSE1113 1 SLING - FAN COWL
 RSE1117 1 THREAD PROTECTOR - COWL DOOR BOLT

 B. Expendable Parts
 -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
cotter pins 71-13-11 01A-010
 F 『 EEFF : ALL E Page 40571-13-11
 E E Aug 01/04 E E ECES E E 56-5B E

 F  『
 E  C F M  E
 E  E

 E E

 C. Referenced Information
 -------------------------------------------------------------------------------
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 1(108)