- Make sure that the quantity of oil in the oil tank of the engine 1(2) is correct.

 - If necessary, fill the oil tank (Ref. TASK 12-13-79-610-002) or (Ref. TASK 12-13-79-610-002).

- The ON legend of this pushbuttonswitch comes on.

 On the lower ECAM display unit, on the ENGINE page:

 - The symbol for the starter valve is in the open position.

 NOTE : During cold weather, large oil pressure surges can occur.

____
 NOTE : A pressure relief valve in the lubrication unit limits the oil

____ pressure to 305 psi (21 bar).
 NOTE : The oil level in the oil tank can go down by 1.6 USgal (6 l) during
____ start.
 NOTE : If a starter air pressure is used that is less than the recommended
____ quantity, slow N2 acceleration and subsequent rpm stop can occur.
 NOTE : Make sure that you do not go over the starter limits that follow:
____
 - no engagement of the starter when the core speed is above 20 percent.
 F 『 EEFF : ALL E Page 52571-00-00
 E E May 01/04 ERE
ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
- the acceptable duty cycles can be performed by using one the three following procedures:

 - 4 consecutive cycles, each of 2 minutes duration with a 20 second rest between 2 consecutive attempts. After 4 cycles, wait 15 minutes to allow starter to cool before you try a new start or motoring. - one 5 minute cycle followed by a cooling period of 2 minutes after the first motoring and a 10 minutes interval between the following ones. - one 15 minute cycle followed by a 15 minute cooling period before you try a new start or motoring. It is recommended to use the 15 minute cycle only for cooling the engine to do a borescope inspection.

 NOTE : While the engine is motored, do a visual check for leaks at the fuel
____
 and oil system tubes and manifolds.

 7. On the overhead CTL & IND panel 22VU:
- Release the ENG/MAN START/1(2) pushbutton switch.
 8. On the ENG panel 115VU:
- Set the ENG/MODE/CRANK/NORM/IGN/START selector switch to NORM.
 9. On the ECAM control panel:
- Get the ENGINE page.
10. On the lower ECAM display unit, on the ENGINE page:
- After a minimum of 5 minutes after the end of the test, look at the oil level indication.
- The ON legend of this pushbuttonswitch goes off.

 On the lower ECAM display unit, on the ENGINE page:

 - The symbol for the starter valve is in the closed position.

On the lower ECAM display unit:

- The ENGINE page goes out of view.

On the lower ECAM display unit:

- The ENGINE page comes into view.

If necessary, fill the oil tank(Ref. TASK 12-13-79-610-002) or(Ref. TASK 12-13-79-610-002).
 F 『 EEFF : ALL E Page 52671-00-00
 E E May 01/04 ERE
ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
11. After engine shutdown, when the  - The OFF legends of these pushbutton rotor movement stops, on the switches come on. HYD/FUEL panel 40VU:
 - Release all the FUEL/PUMPS
 pushbutton switches.

 12. Close the circuit breaker On the upper ECAM display unit:
 1KC1(2) to close the LP valve.  - The ENG 1(2) LP VALVE OPEN message goes out of view.
 The master CAUT light goes off.
 Subtask 71-00-00-200-052
 B. Listen for unusual noise.
 (1) During engine coastdown, while the components continue to turn, listen for unusual noise from these components.
 NOTE : Clicking fan blades, gear noise and seal rubs are normal
____
 noise.

 Subtask 71-00-00-210-052
 C. Do a general visual inspection.
 NOTE : Hydromechanical Units (HMUs) that have fluorocarbon (Viton)
____ external seals (SB 73-015) can leak fuel for a short time when they are below 0 deg.C (32.00 deg.F) (Modification 1 and 2)
R  (Ref. TASK 71-00-00-790-002).
 (1) Make a check of the engine, fan frame and turbine for unusual roughness.

 (2) Make an inspection of the lubrication system lines, fittings and accessories for leaks (Ref. TASK 79-00-00-210-003).

 5. Close-up
________
 Subtask 71-00-00-862-058
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 1(39)