(2) Do a check of the electrical connectors of the aft and forward junction boxes for correct condition.
(3) Do a check of the exposed pylon for correct condition.
(4) Do a check of the forward and aft engine mounts for condition and attachment.
Subtask 71-00-00-110-052
F. Clean bolts (85) and (135), nuts (120) and (155) with trichloroethylene (1,1,1) (Material No. CP1008).
Subtask 71-00-00-210-063
G. Make sure that there are no signs of important seizure or wear. Subtask 71-00-00-230-051
H. Do a fluorescent penetrant inspection level 3 of the mount bolts. No cracks are permitted. See CFMI standard Practices Manual (Ref. SPM 703213) and (Ref. SPM 703223).
F 『 EEFF : ALL E Page 43871-00-00
E E May 01/05 ERE
ECES E Subtask 71-00-00-110-053
F 『
E C F M E
E E
E 56-5B E
E E
J. Carefully clean the mating faces, the shear or locating pin holes and the fastener holes.
Subtask 71-00-00-869-180
K. If some equipment is not installed on the new engine, remove it from the removed engine. Then install it on the new engine.
Subtask 71-00-00-941-069
L. Put foam rubber protective pads between:
- The aft mount and the engine
- Forward mount and engine
- And at the upper part of the fan case so that the parts cannot hit during hoisting operations.
(1) At the half upper part of the fan frame, seal the fan duct panels with adhesive tape.
Subtask 71-00-00-010-097
M. If installed, remove the fuel overboard drain tube at the rear of the drain mast. (Ref. Fig. 407/TASK 71-00-00-991-929)
(1) Disconnect the fuel overboard drain tube (150) from the CFMI tube.
(2) Remove the bolt (155), the nut (160), and the clamp (165) that attach the drain tube (150) to the bracket on the transfer gearbox.
(3) Remove the bolt (170), the spacer (180), and the nut (185) that attach the drain tube (150) to the bracket at the bottom of the transfer gearbox.
(4) Remove the drain tube (150) from the engine.
(5) Put protective covers on the tubes.
F 『 EEFF : ALL E Page 43971-00-00
E E May 01/05 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
INTENTIONALLY BLANK
F 『R E E Page 44071-00-00
E E May 01/05 E E ECES E 4. Procedure
F 『
E C F M E
E E
E 56-5B E
E E
_________ Subtask 71-00-00-480-062
A. Installation of the booststrap:
(1) Install the engine trolley complete with the engine cradle and the replacement engine under the pylon.
(2) Install chain pulley blocks on the bootstrap system.
(3) Attach the chain hooks to the engine cradle.
(4) Free the pins attaching the engine cradle to the trolley.
(5) Place the locking levers of the handling hoist in up position.
(6) Raise the engine cradle to disengage it from the trolley. CAUTION : MAKE SURE THAT THE PYLON FORWARD MOUNT DOES NOT TOUCH THE
_______ UPPER STRUT OR THE UPPER SEAL ASSY WHEN YOU RAISE THE ENGINE OR DAMAGE CAN OCCUR.
(Ref. Fig. 401/TASK 71-00-00-991-910)
(a) Slightly raise the forward section of the engine cradle then the aft section.
NOTE : During hoisting procedure make sure that:
____
- The difference of load between front cables is less than 600 daN (1348.9 lbf) (612 kg)
- The difference of load between rear cables is less than 200 daN (449.6 lbf) (204 kg).
NOTE : Use the level indicators on the forward hinge arms of the
____ bootstrap to keep this hinge arms as near as possible to the horizontal position.
(7) When the distance between the engine mounts and the pylon mounts is approximately 10 mm (0.4 in.) , slowly raise the engine.
CAUTION : DO NOT INSTALL THE LOCATING PINS OF ONE MOUNT BEFORE THE
_______ OTHER OR DAMAGE TO MOUNTS AND PYLON COULD RESULT.
(a) Install front and rear locating pins.
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 動力裝置 POWER PLANT 1(24)
